修复你的物品 社区 商店

Interlink VP4550 Laser Replacement

你所需要的

  1. Interlink VP4550 Laser Replacement, Case: 步骤 1 中的图像 1，3 Interlink VP4550 Laser Replacement, Case: 步骤 1 中的图像 2，3 Interlink VP4550 Laser Replacement, Case: 步骤 1 中的图像 3，3

    • Turn the phone over to where the battery compartment resides.

    • Remove the battery compartment door by pushing down on the door with your thumbs and sliding the door off of the bottom of the device.

    • Remove battery.

    编辑

  2. Interlink VP4550 Laser Replacement: 步骤 2 中的图像 1，3 Interlink VP4550 Laser Replacement: 步骤 2 中的图像 2，3 Interlink VP4550 Laser Replacement: 步骤 2 中的图像 3，3

    • Use a Phillips #0 screwdriver to remove the screw in the middle of the battery compartment.

    • Pry open the case body with the plastic opening tool. Start at the bottom of the device and work toward the top. You will hear a "click" sound as the sides open.

    编辑

  3. Interlink VP4550 Laser Replacement: 步骤 3 中的图像 1，2 Interlink VP4550 Laser Replacement: 步骤 3 中的图像 2，2

    • There is a wire connector linking the front and the back of the device.

    • Carefully pull the wire connectors out of the white connector gauge to completely separate the front and back pieces.

    编辑

  5. Interlink VP4550 Laser Replacement: 步骤 4 中的图像 1，2 Interlink VP4550 Laser Replacement: 步骤 4 中的图像 2，2

    • The power button may fall off when you separate the front and back of the device. This can simply be placed back when reassembling.

    • Find the lever on the right side of the back half of the device.

    • Insert the tip of the lever into the square indent on the underside of the button.

    编辑

  6. Interlink VP4550 Laser Replacement, Circuit Board: 步骤 5 中的图像 1，1

    • Avoid picking up the front of the device as you work so that loose parts will not shift.

    • Use a Phillips #0 head screwdriver to remove two screws; one on either side of the circuit board.

    编辑

  7. Interlink VP4550 Laser Replacement: 步骤 6 中的图像 1，1

    • Slide the circuit board down from the tab located underneath the top of the back half

    • The laser is attached to the circuit board and will slide out of its own housing as you slide out the circuit board.

    • Use tweezers to gently remove it if it doesn't come out.

    编辑

  8. Interlink VP4550 Laser Replacement, Laser: 步骤 7 中的图像 1，1

    • Use desoldering braid to remove the red and black wires attached to both the circuit board and the laser bulb.

    • When you are ready to attach the new laser bulb, use a soldering iron to solder the new bulb's wires to the circuit board.

    编辑
终点

作者

与4其他贡献者

Alayna Bruney

于02/11/14注册

1 声望

撰写一个指南

徽章: 4

+1个徽章

团队

Ohio State, Team 1-1, Buehl Spring 2014 Ohio State, Team 1-1, Buehl Spring 2014 的会员

OSU-BUEHL-S14S1G1

4 名成员

创作了3篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 0

过去 30 天： 0

总计 160