修复你的物品 社区 商店

Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement

简介

The Insignia Flex 10.1 NS-P10W8100 motherboard is connected to several Zero Insertion Force (ZIF) connectors and ribbon cable connectors. Be sure you have unplugged every connector before attempting to free the motherboard.

你所需要的

  1. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement, Motherboard: 步骤 1 中的图像 1，2 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement, Motherboard: 步骤 1 中的图像 2，2

    • Carefully open the laptop and remove the keyboard by disconnecting it.

    • Place keyboard to the side as you will not need it.

    • Beware of plastic clips on the side of the device.

    编辑

  2. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 2 中的图像 1，2 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 2 中的图像 2，2

    • Lay the screen flat on its surface and use the iFixit opening tool to remove the cover by gently prying the back cover from the screen.

    • Apply the opening tool to the edge closest to the screen.

    • Apply the opening tool to each side which will help pry the back cover evenly.

    • Do not pry on the bottom side of the device. This is the side across from the camera.

    编辑

  3. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 3 中的图像 1，1

    • Use your fingers and pry the back cover from the screen. You may need to wiggle the cover a bit to separate the pieces.

    • If the back cover does not come off, work your fingers around the corners and slowly pry the cover off using your fingers.

    • Be careful with potential sharp edges and any exposed electrical components.

    编辑

  4. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 4 中的图像 1，3 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 4 中的图像 2，3 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 4 中的图像 3，3

    • Gently remove the black tape from each of the three connectors.

    • It may help to move around the motherboard in a clockwise direction to remove each piece of tape.

    编辑

  5. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 5 中的图像 1，1

    • With a fingernail, gently remove the yellow tape from across the speaker wires.

    编辑

  7. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 6 中的图像 1，1

    • Once the pieces of tape are removed the resulting motherboard should look like this picture.

    • The ZIF connectors will be removed in a clockwise motion.

    • Secondly, the ribbon cable connectors will be unplugged to isolate the motherboard.

    编辑

  8. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 7 中的图像 1，2 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 7 中的图像 2，2

    • Unplug the smallest ZIF Connector by using you fingernail to flip up the small locking flap. Then safely pull the cable out.

    • Be careful not too pull too hard as the ZIF Connector is fragile and can be damaged easily.

    编辑

  9. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 8 中的图像 1，2 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 8 中的图像 2，2

    • Following a clockwise direction, continue unplugging the ZIF connectors by safely puling the cable out.

    编辑

  10. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 9 中的图像 1，1

    • Remove the ribbon cables by firstly disconnecting the cable located on the top right of the motherboard,

    • Be careful not to forcefully yank the cable as it could cause a wire to disconnect.

    编辑

  11. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 10 中的图像 1，1

    • Remove the remaining two bottom ribbon cables.

    编辑

  12. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 11 中的图像 1，3 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 11 中的图像 2，3 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 11 中的图像 3，3

    • Disconnect the three low profile connectors by using a spudger to prop up both sides. Then, lift the connectors straight up from their sockets.

    编辑

  13. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 12 中的图像 1，3 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 12 中的图像 2，3 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 12 中的图像 3，3

    • Using a Phillips #2 screwdriver, remove the three 4 mm screws to free the motherboard.

    编辑

  14. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 13 中的图像 1，2 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 13 中的图像 2，2

    • Pull the two pieces of grey tape off the motherboard.

    编辑

  15. Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 14 中的图像 1，2 Insignia Flex 10.1 NS-P10W8100 Motherboard Replacement: 步骤 14 中的图像 2，2

    • Remove the motherboard by lifting it upward.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

0条评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 2

过去 30 天： 5

总计 597