简介

This guide shows you how to replace the motherboard of your Huawei P8 Lite.

  1. Use an Opening Tool and start to lever up the back cover of your Huawei P8 Lite at the bottom of your phone.
    • Use an Opening Tool and start to lever up the back cover of your Huawei P8 Lite at the bottom of your phone.

    添加评论

  2. There are clips around the whole mid frame, holding down the back cover. Open all of them with the Opening Tool.
    • There are clips around the whole mid frame, holding down the back cover. Open all of them with the Opening Tool.

    • When all clips are open, remove the back cover from the rest of the phone.

      • If the back cover doesn't come freely, there are probably some additional clips that need to be disconnected.

    The back panel is really really easy to brake, be careful :)

    romaingauthier - 回复

    • Use a tweezer to remove the warranty sticker which sits on a screw in the bottom right of your phone.

    The 4 screws wich hold down the lower part of the loudspeaker are Torx screws for me. But it's a French Huawei, doin' nothing like the others :)

    Christopher Hourlier - 回复

    Die Wasserschadenindikatoren sitzen unter dem Mainboard. Bei den Aufklebern auf den TORX handelt es sich um Garantiesiegel.

    Andre Richter - 回复

    Danke für den Hinweis, wurde so übernommen.

    Dominik Schnabelrauch -

    pour dévisser les vis cruciformes, quel taille de tournevis faut il? svp

    blan - 回复

    Bonjour, il vous faut un tournevis ou un embout cruciforme #00 pour dévisser une vis cruciforme #00. Bonne réparation !

    Claire Rapp -

    • Remove the 4 black Torx T5 screws which hold down the lower part of the loudspeaker.

    • Remove the three silver Phillips #00 screws which hold down the upper part of the loudspeaker.

    添加评论

    • Remove the loudspeaker carefully.

    添加评论

    • Remove the three Phillips #00 screws that hold the metal plate in place.

    • Remove the metal plate with a tweezer.

    • Unplug the battery flex connector with a spudger.

    Theese Screws are quite hard to remove…

    Jannik Peichl - 回复

    • Remove the two Torx T5 screws.

      • If there is a tamper evident sticker over your screws remove them to properly seat your driver.

    • Remove the five Phillips #00 screws.

    添加评论

    • Carefully pry off the plastic cover on the left side. The NFC antenna contacts might be slightly glued to the cover.

    • Then remove the top cover.

    An der Linken Plastikabdeckung sind die Kontakte dran geklebt!

    Luk_ S!lver - 回复

    • Remove the SIM card and SD card trays.

    • Disconnect the three plug connectors and one ZIF connector.

      • Unlock the ZIF connector by lifting the small black plastic lever.

    添加评论

    • Remove the volume and power button cable.

    • Take out the motherboard by lifting the bottom part first.

      • Pay attention to the cables, so they don't rip when staying stuck to the motherboard.

    • On the back of the motherboard there is a thermal pad (pink rubber-like gob) for heat dissipation. If this thermal pad broke or is too dried out you might want to replace it with a new one.

    添加评论

结论

To reassemble your device, follow these instructions in reverse order and apply adhesive where necessary.

4等其他人完成本指南。

Tobias Isakeit

于2014年03月31日注册

34,354 信誉积分

创作了87篇指南

团队

iFixit iFixit 的会员

Community

114 名成员

创作了7,024篇指南

添加评论

浏览统计数据:

过去的24小时: 13

过去的7天: 82

过去的30天: 321

总计 3,825