简介

Brakes slow your bike down when you pull on the brake lever on the handlebar. The brake calipers are connected to the brake levers by a cable that squeezes the brake-pads that are attached to the brake calipers. When the brake pads contact the rims they slow down the rim of the wheel, slowing down the bike.

Squeeze the calipers together, and remove the brake cable.
  • Squeeze the calipers together, and remove the brake cable.

添加评论

Loosen the break caliper bolt, and remove the brake caliper.
  • Loosen the break caliper bolt, and remove the brake caliper.

添加评论

  • Inspect the brake pad. If the pad has worn down past the “wear line”, then it needs to be replaced.

添加评论

  • Clean and lubricate the parts as necessary before reattaching the caliper arms.

  • Bolt the caliper arms back on while making sure the the pin on the back side of the caliper arm lines back up with the one of the holes in the frame. Each side should be in the same hole.

添加评论

  • Reattach the brake cable to the calipers.

添加评论

  • Loosen the brake pad bolt.

添加评论

  • Get an ordinary piece of paper, and fold it twice over.

  • Place the sheet of paper between the brake pad and the rim in the position shown.

What's the reason of doing this? Is it to keep 1 or 2 mm gap between the pad and rim or to 'toe-in' the break bad?

Seamuzzaman Nahid - 回复

Helps to prevent brake chatter by feathering in the pads to the rim.

R I - 回复

  • Align the brake pad so that it is flush with the rim, with no part touching the rubber of the tire.

  • Have somebody clamp down very tightly on the brakes.

  • Tighten the brake pad bolt in place.

The brake lever could also be held down with a cable tie, velcro strap, or a strong elastic band

R I - 回复

  • Tighten/loosen the tension adjustment screws on each the caliper arm to adjust the resting distance of each brake pad, so that each pad is equally distant from the rim. Tightening the screw will shift the caliper outward from the bike, loosening it will shift it inward.

  • Tighten/loosen the brake adjuster on the handle bars such that when you clamp down on the brakes, the brake lever stops before hitting the handle bar. This will set the distance between the brake pads and the rim.

  • Tighten the lock nut on the brake adjuster to permanently set its position.

Very good!,Was wondering about some small details . This clered it out. Thx

Tim Brumen - 回复

终点

32等其他人完成本指南。

Travis Tonder

于2010年10月05日注册

2,462 信誉积分

创作了5篇指南

团队

Cal Poly, Team 5-13, Maness Fall 2010 Cal Poly, Team 5-13, Maness Fall 2010 的会员

CPSU-MANESS-F10S5G13

4 名成员

创作了11篇指南

[|what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? what does it mean if the point is red????? IS IT OKAY?????? IS IT OKAY??????]

Merpface - 回复

The red bullet point seems to correspond with the red circle in the image.

Victor Chan -

help me please

Merpface - 回复

yyyyyaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa

Merpface - 回复

“what does it mean if the point is red???? “

I believe that is indicating that this step corresponds to an image which highlights a specific step. I saw this two times, in step 4 and step 9. For step 4, it shows the highlight in the second image and for step 9, the highlight is in the first image. It seems that the red bullet point is just to make it easier to map the step to the image.

Hope this helps

Tony - 回复

添加评论

浏览统计数据:

过去的24小时: 51

过去的7天: 459

过去的30天: 1,982

总计 51,124