修复你的物品 社区 商店

How to change Tool for DeepAccess

你所需要的

  1. How to change Tool for DeepAccess, How to change Tool for DeepAccess: 步骤 1 中的图像 1，1

    • Prepare Tools and replacement parts.

    编辑

  2. How to change Tool for DeepAccess, Remove wedge from transducer: 步骤 2 中的图像 1，3 How to change Tool for DeepAccess, Remove wedge from transducer: 步骤 2 中的图像 2，3 How to change Tool for DeepAccess, Remove wedge from transducer: 步骤 2 中的图像 3，3

    • Grab wegdge with tweezers

    • Loosen the screw. (while holding the wedge)

    • Get rid of the copper screw. To NOT use it more than once

    编辑

  3. How to change Tool for DeepAccess, Place the new wedge in the transducer.: 步骤 3 中的图像 1，3 How to change Tool for DeepAccess, Place the new wedge in the transducer.: 步骤 3 中的图像 2，3 How to change Tool for DeepAccess, Place the new wedge in the transducer.: 步骤 3 中的图像 3，3

    • Put the wedge in the tranducer from below.

    • Take care, that the Tool Top is flush with the Transducer surface

    • Correct Placement. Tool is flush with transducer.

    • Incorrect Placement. tool is too high.

    编辑

  5. How to change Tool for DeepAccess, Fasten the copper screw: 步骤 4 中的图像 1，2 How to change Tool for DeepAccess, Fasten the copper screw: 步骤 4 中的图像 2，2

    • Fasten the screw lightly

    • Tighten the screw just so the wedge does not slip out of the tranducer.

    • in case of appliying too much torque. Use a new screw and get rid of the old one.

    编辑

  6. How to change Tool for DeepAccess, Adjust wedge heigth with setting gauge: 步骤 5 中的图像 1，3 How to change Tool for DeepAccess, Adjust wedge heigth with setting gauge: 步骤 5 中的图像 2，3 How to change Tool for DeepAccess, Adjust wedge heigth with setting gauge: 步骤 5 中的图像 3，3

    • Place gauge below Tool

    • Loosen the screw so the wedge slides onto the gauge Lever.

    • Lift the gauge up until in contact with the transducer horn.

    • Now the Tool-Top should be flush with the Transducer-Horn

    • Tighten the screw with the torque- wrench

    • Use Torque wrench with 18cN limitation

    编辑

    • Use tweezers to push the wire down the wire hole, until it Ends some cm below the tool wedge.

    • Use scissors to cut the (contaminated) Wire down to a length of about 1cm below wedge end.

    编辑

  8. How to change Tool for DeepAccess, Thread Wire through Wedge-hole: 步骤 7 中的图像 1，3 How to change Tool for DeepAccess, Thread Wire through Wedge-hole: 步骤 7 中的图像 2，3 How to change Tool for DeepAccess, Thread Wire through Wedge-hole: 步骤 7 中的图像 3，3

    • Use tweezers to thread the wire through the hole at the end of the wedge.

    • Afet threading pull the wire some cm through the hole.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

作者

与1其他贡献者

Hans Panz

于03/10/16注册

289 声望

创作了2篇指南

徽章: 2

0条评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 0

过去 30 天： 0

总计 54