修复你的物品 加入社区 商店

How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822

简介

Sometimes the moving about of computer speakers leads to broken wires and the speakers will fail to work properly. This guide will show you how to repair a Harman Kardon CN-04N567-48220 external computer speaker.

你所需要的

  1. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822, How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: 步骤 1 中的图像 1，3 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822, How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: 步骤 1 中的图像 2，3 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822, How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: 步骤 1 中的图像 3，3

    • Use your fingers to pull the top of the speaker grill away from the speaker enclosure.

    • Pull the bottom of the grill away from the speaker enclosure and then completely remove the grill.

    • Four posts attach the grill assembly to the front of speaker enclosure. These posts are located on the back side of the grill assembly.

    编辑

  2. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: 步骤 2 中的图像 1，2 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: 步骤 2 中的图像 2，2

    • Remove the top two 9.5 mm Phillips #1 screws from the speaker.

    • Remove the two 9.5 mm Phillips #1 screws located below the speaker screws.

    • Slowly work your way around the seam until the two parts of the enclosure are free.

    • More speaker cable slack may be achieved by pulling additional cable through the rear of the case.

    编辑

  3. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: 步骤 3 中的图像 1，2 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: 步骤 3 中的图像 2，2

    • Inspect both sides of the printed circuit board (PCB) for any raised traces, off-colored areas, or loose components.

    • This step is to avoid making a mechanical repair (re-soldering the wires to the PCB) on a piece of equipment that also has obvious electrical or mechanical issues.

    编辑

  5. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: 步骤 4 中的图像 1，1

    • Use desoldering braid and a soldering iron to wick away the old solder and wire remnants from the solder pads and through-holes.

    • Do not leave solder bridges across the pads as this will cause functional issues.

    编辑

  6. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: 步骤 5 中的图像 1，2 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: 步骤 5 中的图像 2，2

    • Use wire strippers to remove a small section of insulation from the wires.

    • Use a soldering iron and solder to tin the wires. This prevents the strands from fraying.

    编辑

  7. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: 步骤 6 中的图像 1，2 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: 步骤 6 中的图像 2，2

    • Insert the yellow wire into the through-hole marked "R".

    • Insert the bare ground wire into the through-hole marked "G".

    • Insert the white wire into the through-hole marked "L".

    编辑

  8. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: 步骤 7 中的图像 1，1

    • Use the soldering iron to flow solder between each wire and its solder pad.

    编辑

  9. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: 步骤 8 中的图像 1，1

    • Reassemble the two parts of the enclosure making sure that the PCB-mounted audio jacks are lined up with the mating holes of the rear enclosure.

    • Route the cable inside the enclosure to avoid stressing the solder joints.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

7等其他人完成本指南。

作者

与2其他贡献者

Ken Gage

于06/09/16注册

285 声望

撰写一个指南

徽章: 6

+ 3更多徽章

团队

Texas Tech, Team 3-1, Rauch SU 2016 Texas Tech, Team 3-1, Rauch SU 2016 的会员

TTU-RAUCH-SU16S3G1

2 名成员

创作了2篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 1

过去 7 天： 11

过去 30 天： 48

总计 4,100