跳转到主内容

Hover-1 Nomad LED Headlights Replacement

你所需要的

  1. Hover-1 Nomad LED Headlights Replacement, Outer Shell: 步骤 1 中的图像 1,3 Hover-1 Nomad LED Headlights Replacement, Outer Shell: 步骤 1 中的图像 2,3 Hover-1 Nomad LED Headlights Replacement, Outer Shell: 步骤 1 中的图像 3,3
    • Break the two warranty stickers by poking a screwdriver through them or peeling them off.

    • Remove the following twenty screws by rotating the screwdriver counterclockwise:

    • Eight 16.2mm Phillips #2 screws

    • Eight 15mm Phillips #2 screws

    • Four 19.1mm Phillips #2 screws

    • The holes containing most of the screws are deep and narrow. A screwdriver with interchangable bits will not be able to reach them.

    • Do not over-tighten the screws during reassembly. Over-tightened screws can crack the plastic channels holding the shell to the frame of the hoverboard.

  2. Hover-1 Nomad LED Headlights Replacement: 步骤 2 中的图像 1,3 Hover-1 Nomad LED Headlights Replacement: 步骤 2 中的图像 2,3 Hover-1 Nomad LED Headlights Replacement: 步骤 2 中的图像 3,3
    • Use a nylon spudger to pry the metal handle away from the outer shell.

    • Rotate the metal handle toward the center of the hoverboard to unlock the plate from the retaining clips.

    • Lift the hoverboard off the metal handle.

    • Repeat for the handle on the other side of the hoverboard.

  3. Hover-1 Nomad LED Headlights Replacement: 步骤 3 中的图像 1,1
    • Lift the plastic cover on each side up and away from the device.

    • Multiple wires connect the circuit boards to the outer shell. Remove the shell gently to avoid damaging the wires or components.

  4. Hover-1 Nomad LED Headlights Replacement: 步骤 4 中的图像 1,2 Hover-1 Nomad LED Headlights Replacement: 步骤 4 中的图像 2,2
    • Disconnect the following wires by pinching the connector tabs and pulling the plugs out of the connectors:

    • Charging port wires

    • Speaker assembly wires

    • Power button wires

    • Headlight wires

    • Only the headlight wires need to be disconnected from the other circuit board.

    • Ensure the wires are connected to the correct ports on the circuit board during reassembly.

  5. Hover-1 Nomad LED Headlights Replacement, LED Headlights: 步骤 5 中的图像 1,1
    • Remove the two 13mm Phillips #1 screws by rotating the screwdriver counterclockwise.

    • Repeat on the other side of the hoverboard to remove the other headlight.

  6. Hover-1 Nomad LED Headlights Replacement: 步骤 6 中的图像 1,1
    • Pull the headlight up and off the outer shell.

    • Repeat on the other side of the hoverboard to remove the other headlight.

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

Samuel Frazee

于10/08/18注册

1,015 声望

创作了7篇指南

团队

Cal Poly, Team S15-G1, White Fall 2018 Cal Poly, Team S15-G1, White Fall 2018 的会员

CPSU-WHITE-F18S15G1

4 名成员

创作了7篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时: 0

过去 7 天: 0

过去 30 天: 0

总计 231