修复你的物品 社区 商店

Hover-1 Coast Power Button Spring Replacement

简介

If your Hover-1 Coast board’s power button won't press you likely have an issue with the button spring. This spring allows the button to be compressed, sending a signal to the battery to turn on and power the board.

This will be a moderately difficult task to complete as you will use tools that not everyone probably has but are common for most electronics repairs.


Provided to you, is a list of detailed instructions on how to properly, and safely replace the spring. For parts please go ++here++ to look at how to purchase new parts. For any inquiries, please take a look at the operator’s manual link ++here++.

你所需要的

  1. Hover-1 Coast Power Button Spring Replacement, Board Battery: 步骤 1 中的图像 1，3 Hover-1 Coast Power Button Spring Replacement, Board Battery: 步骤 1 中的图像 2，3 Hover-1 Coast Power Button Spring Replacement, Board Battery: 步骤 1 中的图像 3，3

    • To remove the battery on the Hover-1 Coast, you must uncover the screws on the top of the board.

    • Using a pick tool, puncture the grip tape and expose the screws.

    • Loosen all four 1" screws using a Phillips #1 screwdriver.

    编辑

  2. Hover-1 Coast Power Button Spring Replacement: 步骤 2 中的图像 1，3 Hover-1 Coast Power Button Spring Replacement: 步骤 2 中的图像 2，3 Hover-1 Coast Power Button Spring Replacement: 步骤 2 中的图像 3，3

    • Now pull the black protective cover off the board.

    • Locate the battery.

    编辑

  4. Hover-1 Coast Power Button Spring Replacement: 步骤 3 中的图像 1，3 Hover-1 Coast Power Button Spring Replacement: 步骤 3 中的图像 2，3 Hover-1 Coast Power Button Spring Replacement: 步骤 3 中的图像 3，3

    • The battery is connected by these two sets of wires.

    • Remove the yellow wire first by pulling the two wires gently in opposite directions.

    • Now pull apart the black wire by gently pulling the two wires in opposite directions.

    编辑

  5. Hover-1 Coast Power Button Spring Replacement: 步骤 4 中的图像 1，3 Hover-1 Coast Power Button Spring Replacement: 步骤 4 中的图像 2，3 Hover-1 Coast Power Button Spring Replacement: 步骤 4 中的图像 3，3

    • Once the battery has been disconnected, gently pry the battery upward.

    • It is important to use a plastic opening tool to avoid puncturing the battery.

    • Once the battery is freed, remove it with your hands.

    • The battery is glued to the case and will require some effort to remove.

    编辑

  6. Hover-1 Coast Power Button Spring Replacement, Power Button Spring: 步骤 5 中的图像 1，3 Hover-1 Coast Power Button Spring Replacement, Power Button Spring: 步骤 5 中的图像 2，3 Hover-1 Coast Power Button Spring Replacement, Power Button Spring: 步骤 5 中的图像 3，3

    • Using the Phillips #1 screwdriver, loosen the two screws and place the power button somewhere safe.

    编辑

  7. Hover-1 Coast Power Button Spring Replacement: 步骤 6 中的图像 1，2 Hover-1 Coast Power Button Spring Replacement: 步骤 6 中的图像 2，2

    • Remove the unwanted spring and place your new spring back into the hole.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

0条评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 3

过去 30 天： 4

总计 345