跳转到主内容

Hover-1 Chrome Left Gyroscope Sensor Board Replacement

你所需要的

  1. Hover-1 Chrome Left Gyroscope Sensor Board Replacement, Hover-1 Chrome Disassembly: 步骤 1 中的图像 1,1
    • Flip the Hover-1 Chrome upside down.

    • Use a Phillips #2 screwdriver to remove the fourteen 14 mm screws from the bottom of the Hover-1.

    • Break the two black tape circles, and remove the two 15 mm Phillips screws underneath.

  2. Hover-1 Chrome Left Gyroscope Sensor Board Replacement: 步骤 2 中的图像 1,1
    • Lift the shell without the speaker grille and unplug the battery.

  3. Hover-1 Chrome Left Gyroscope Sensor Board Replacement: 步骤 3 中的图像 1,2 Hover-1 Chrome Left Gyroscope Sensor Board Replacement: 步骤 3 中的图像 2,2
    • Lift the shell with the speaker grille.

    • Unplug the speaker.

    • Unplug the LEDs.

    • Unplug the power button

    • Unplug the charging port.

  4. Hover-1 Chrome Left Gyroscope Sensor Board Replacement, Left Gyroscope Sensor Board: 步骤 4 中的图像 1,3 Hover-1 Chrome Left Gyroscope Sensor Board Replacement, Left Gyroscope Sensor Board: 步骤 4 中的图像 2,3 Hover-1 Chrome Left Gyroscope Sensor Board Replacement, Left Gyroscope Sensor Board: 步骤 4 中的图像 3,3
    • Disconnect the speaker cable.

    • Disconnect the cable that travels to the other sensor board.

  5. Hover-1 Chrome Left Gyroscope Sensor Board Replacement: 步骤 5 中的图像 1,3 Hover-1 Chrome Left Gyroscope Sensor Board Replacement: 步骤 5 中的图像 2,3 Hover-1 Chrome Left Gyroscope Sensor Board Replacement: 步骤 5 中的图像 3,3
    • Disconnect the smaller connector midway on the cable.

    • Disconnect the larger connector midway on the cable.

  6. Hover-1 Chrome Left Gyroscope Sensor Board Replacement: 步骤 6 中的图像 1,1
    • Remove the four 12mm Phillips #2 screws securing the sensor board.

  7. Hover-1 Chrome Left Gyroscope Sensor Board Replacement: 步骤 7 中的图像 1,2 Hover-1 Chrome Left Gyroscope Sensor Board Replacement: 步骤 7 中的图像 2,2
    • Locate the five solder locations on the underside of the gyroscope sensor board.

    • Plug in soldering iron and wait for the tip tip to reach its target temperature.

    • Rest the tip of the iron on the solder and wait for the solder to melt. The wire will drop out of the sensor board.

    • Be aware of where the tip of the soldering iron is at ALL times. Put on safety glasses before picking up the soldering iron. Turn on a fan and face it towards the device to vent harmful fumes away from the solderers face.

结论

To reassemble your device, follow these instructions in reverse order.

Nick McGuire

于10/08/18注册

551 声望

创作了4篇指南

团队

Cal Poly, Team S4-G1, White Fall 2018 Cal Poly, Team S4-G1, White Fall 2018 的会员

CPSU-WHITE-F18S4G1

4 名成员

创作了6篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时: 0

过去 7 天: 2

过去 30 天: 10

总计 1,082