修复你的物品 社区 商店

Hipstreet Titan 2 HD Speaker Replacement

简介

Use this guide to replace the speaker. First you'll need to remove the rear cover. This can be a difficult process.

你所需要的

  1. Hipstreet Titan 2 HD Speaker Replacement, Rear Case: 步骤 1 中的图像 1，1

    • Using the PH#00 screwdriver, remove the two 0.145 inch Phillips head screws.

    • The screws are located on the bottom face of the device, near the power and volume controls.

    翻译

  2. Hipstreet Titan 2 HD Speaker Replacement: 步骤 2 中的图像 1，1

    • Place the small suction cup on your screen.

    • Moisturize the bottom of the suction cup to ensure a proper seal.

    • If the screen is cracked, the suction cup may not seal correctly; too much pressure may crack or damage the screen.

    翻译

  3. Hipstreet Titan 2 HD Speaker Replacement: 步骤 3 中的图像 1，1

    • Insert the plastic opening tool between the screen cover and rear cover of the tablet.

    • Grasp the small suction cup.

    翻译

  4. Hipstreet Titan 2 HD Speaker Replacement: 步骤 4 中的图像 1，2 Hipstreet Titan 2 HD Speaker Replacement: 步骤 4 中的图像 2，2

    • Slide the plastic opening tool along device edge to separate the screen cover from the rear cover.

    • Pull upward on the small suction cup handle while sliding the opening tool.

    • When sliding the plastic opening tool, avoid sliding the tool too far into the cover. This could damage the speaker connector on the back cover.

    翻译

  6. Hipstreet Titan 2 HD Speaker Replacement: 步骤 5 中的图像 1，2 Hipstreet Titan 2 HD Speaker Replacement: 步骤 5 中的图像 2，2

    • Use the plastic opening tool to remove the speaker from the rear cover.

    • The speaker is held in place with adhesive and is easily removed.

    • Do not pull on the speaker wires. This could damage the soldering connections.

    翻译

  7. Hipstreet Titan 2 HD Speaker Replacement: 步骤 6 中的图像 1，1

    • Once the speaker is disconnected, the cover removal is complete.

    翻译

  8. Hipstreet Titan 2 HD Speaker Replacement, Speaker: 步骤 7 中的图像 1，1

    • Remove the black placement tape.

    翻译

  9. Hipstreet Titan 2 HD Speaker Replacement: 步骤 8 中的图像 1，1

    • Using a #PH000 screwdriver, remove the three 0.145in circuit board placement screws.

    翻译

  10. Hipstreet Titan 2 HD Speaker Replacement: 步骤 9 中的图像 1，3 Hipstreet Titan 2 HD Speaker Replacement: 步骤 9 中的图像 2，3 Hipstreet Titan 2 HD Speaker Replacement: 步骤 9 中的图像 3，3

    • Lift the hinge locks on the three ribbon connectors and disconnect the ribbon connectors.

    翻译

  11. Hipstreet Titan 2 HD Speaker Replacement: 步骤 10 中的图像 1，1

    • Identify the two soldered connectors for the speaker.

    翻译

  12. Hipstreet Titan 2 HD Speaker Replacement: 步骤 11 中的图像 1，1

    • Using a solder removal tool, remove the speaker soldered connectors.

    • Solder the new speaker wire connections to circuit board.

    • First solder the red wire on the left, then the black wire on the right.

    • Solder can burn you. Use caution.

    翻译
结论

To reassemble your device, follow these instructions in reverse order.

2等其他人完成本指南。

作者

与7其他贡献者

Jeffrey

于03/11/15注册

766 声望

创作了5篇指南

徽章: 10

+ 7更多徽章

团队

Colorado Springs, Team 5-6, Panko Spring 2015 Colorado Springs, Team 5-6, Panko Spring 2015 的会员

UCCS-PANKO-S15S5G6

3 名成员

创作了10篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 0

过去 30 天： 0

总计 304