Skip to main content

介绍

The HTC Vive's focus knob may wear down or crack with use. This guide will show you how to replace the Vive's focus knob.

  1. Slide the HTC panel covering the cables forward, away from the Vive. Gently pull on each of the four connectors to remove the sound and Three-in-One cables. Gently pull on each of the four connectors to remove the sound and Three-in-One cables.
    • Slide the HTC panel covering the cables forward, away from the Vive.

    • Gently pull on each of the four connectors to remove the sound and Three-in-One cables.

  2. Undo the hook and loop tape on the straps.
    • Undo the hook and loop tape on the straps.

    • Slide the ends of the straps through the hinge loops.

  3. Pull the facerest cushion off away from the Vive, separating the hook and loop tape.
    • Pull the facerest cushion off away from the Vive, separating the hook and loop tape.

  4. Android 维修工具包

    一个新的屏幕或电池就在一个套件之内。

    现在开始购物

    Android 维修工具包

    一个新的屏幕或电池就在一个套件之内。

    现在开始购物
  5. Use a T6 Torx Screwdriver to remove  either of the two 12mm hinge screws holding the two hinges in place. Allow the hinge to fall away once the screw is removed.
    • Use a T6 Torx Screwdriver to remove either of the two 12mm hinge screws holding the two hinges in place.

    • Allow the hinge to fall away once the screw is removed.

    • Repeat for the opposite side.

  6. Slide the plastic facerest away from the device. Slide the plastic facerest away from the device. Slide the plastic facerest away from the device.
    • Slide the plastic facerest away from the device.

  7. Orient the Vive so that the camera is facing towards you and the connector ports are facing upwards. There are four screws you need to remove that are covered with small black stickers (two on top, two on bottom). Use a plastic opening tool to gently pry up the left side of the outer sheath.
    • Orient the Vive so that the camera is facing towards you and the connector ports are facing upwards.

    • There are four screws you need to remove that are covered with small black stickers (two on top, two on bottom).

    • Use a plastic opening tool to gently pry up the left side of the outer sheath.

    • If the left sheath is glued down, slide your plastic opening tool along the middle seam to break the bond.

    • Slide the left side of the sheath outwards.

  8. Slide a plastic opening tool underneath the right side of the sheath to remove any remaining glue. Using the plastic opening tool, pry the right side of the sheath upwards slightly. Using your hands, slide the right side of the sheath outwards.
    • Slide a plastic opening tool underneath the right side of the sheath to remove any remaining glue.

    • Using the plastic opening tool, pry the right side of the sheath upwards slightly.

    • Using your hands, slide the right side of the sheath outwards.

  9. Remove the focus knob by unscrewing one 4mm #00 Philips head screw. Pull the knob outwards from the device.
    • Remove the focus knob by unscrewing one 4mm #00 Philips head screw.

    • Pull the knob outwards from the device.

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

Caleb Watts

于2017年09月25日注册

1,560 Reputation

创作了11篇指南

Team

Cal Poly, Team S18-G1, Forte Fall 2017 Cal Poly, Team S18-G1, Forte Fall 2017 的会员

CPSU-FORTE-F17S18G1

5 名成员

创作了11篇指南

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 5

Past 30 Days: 21

All Time: 633