Flip the HP iPAQ HW6515 over with the screen facing down. Take the back cover off by pressing on the small silver button while pulling back then up on the case. Place the back of the case aside for now.
  • Flip the HP iPAQ HW6515 over with the screen facing down.

  • Take the back cover off by pressing on the small silver button while pulling back then up on the case.

  • Place the back of the case aside for now.

添加评论

Remove the battery by pulling up on the black tab.
  • Remove the battery by pulling up on the black tab.

添加评论

Unscrew the four outside screws using the T6 hexagonal star screwdriver. Unscrew the inside middle screw using a Phillips 00 screwdriver. "Warranty VOID if broken" sticker might be covering the middle screw, if this is the case, peel it off to reveal the screw.
  • Unscrew the four outside screws using the T6 hexagonal star screwdriver.

  • Unscrew the inside middle screw using a Phillips 00 screwdriver.

  • "Warranty VOID if broken" sticker might be covering the middle screw, if this is the case, peel it off to reveal the screw.

添加评论

Mac RAM 套件
加速你的Mac。充分利用它的内存。
Mac RAM 套件
从Mac中清理出更多内存。
Use the plastic opening tool to pry apart the covers along the bottom of the phone. Slide the plastic opening tool along the seam until the two halves of the case separate. Slide the plastic opening tool along the seam until the two halves of the case separate.
  • Use the plastic opening tool to pry apart the covers along the bottom of the phone.

  • Slide the plastic opening tool along the seam until the two halves of the case separate.

添加评论

Unplug the sensor wire that connects the two halves of the case before pulling the two halves apart. Not doing so will damage the sensor wire. Unplug the sensor wire that connects the two halves of the case before pulling the two halves apart. Not doing so will damage the sensor wire. Unplug the sensor wire that connects the two halves of the case before pulling the two halves apart. Not doing so will damage the sensor wire.
  • Unplug the sensor wire that connects the two halves of the case before pulling the two halves apart. Not doing so will damage the sensor wire.

添加评论

Use a 00 Phillips screwdriver to remove the three small screws holding down the motherboard.
  • Use a 00 Phillips screwdriver to remove the three small screws holding down the motherboard.

添加评论

Peel back the black tape that covers the connector.
  • Peel back the black tape that covers the connector.

  • It is fine if one of the left connectors comes off along with the tape.

添加评论

Lift the black tab to a 45 degree angle. Use a screwdriver to get under the tape and disconnect the tape from the black tab. Use a screwdriver to get under the tape and disconnect the tape from the black tab.
  • Lift the black tab to a 45 degree angle.

  • Use a screwdriver to get under the tape and disconnect the tape from the black tab.

添加评论

Gently pry the motherboard out of the front casing, bottom first. Disconnect the wire connecting the motherboard to the front casing. Using too much force will damage this wire.
  • Gently pry the motherboard out of the front casing, bottom first.

  • Disconnect the wire connecting the motherboard to the front casing. Using too much force will damage this wire.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

Ashley Schaefer

于2012年04月04日注册

83 信誉积分

创作了2篇指南

团队

Cal Poly, Team 15-17, Forte Spring 2012 Cal Poly, Team 15-17, Forte Spring 2012 的会员

CPSU-FORTE-S12S15G17

4 名成员

创作了5篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 1

总计 940