修复你的物品 社区 商店

HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement

简介

This guide goes over how to replace the controller's main circuit board.

If your TPC-Q044 circuit board starts failing when using your controller, you may want to think about replacing the component. The failure may be a result of bad soldering or missed connections. The replacement of the circuit board is not too complex. A couple of screwdrivers and a spudger will be sufficient to complete this task. There are no warnings or potential hazards when replacing the board.

你所需要的

  1. HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement, Batteries: 步骤 1 中的图像 1，3 HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement, Batteries: 步骤 1 中的图像 2，3 HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement, Batteries: 步骤 1 中的图像 3，3

    • Slide the rear compartment cover in the direction of the arrow.

    • If replacing batteries, ensure the (+) and (-) on the battery match the (+) and (-) labeled in the battery compartment.

    编辑

  2. HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement, Shell: 步骤 2 中的图像 1，2 HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement, Shell: 步骤 2 中的图像 2，2

    • Remove the four 4mm screws using a Phillips #00 screwdriver.

    编辑

  3. HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement: 步骤 3 中的图像 1，3 HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement: 步骤 3 中的图像 2，3 HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement: 步骤 3 中的图像 3，3

    • Grip the main body and pull the joystick outwards until the entire front panel pops off.

    • Remove the 6mm screw in the corner of the joystick well using a Phillips #00 screwdriver.

    编辑

  5. HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement: 步骤 4 中的图像 1，2 HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement: 步骤 4 中的图像 2，2

    • Use a spudger to pry apart the two halves of the assembly.

    • Work slowly, prying a small section at a time until the halves are completely separated.

    编辑

  6. HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement, Small Circuit Board: 步骤 5 中的图像 1，2 HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement, Small Circuit Board: 步骤 5 中的图像 2，2

    • Using a Phillips #00 screwdriver, remove the four 4mm screws located on the joystick circuit board underneath the top half of the controller.

    编辑

  7. HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement: 步骤 6 中的图像 1，3 HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement: 步骤 6 中的图像 2，3 HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement: 步骤 6 中的图像 3，3

    • Remove the orange flat cable by pulling the orange tab parallel to the circuit board.

    • Release the blue flat cable by lifting up the white latch with a spudger.

    编辑

  8. HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement, Main Circuit Board: 步骤 7 中的图像 1，3 HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement, Main Circuit Board: 步骤 7 中的图像 2，3 HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement, Main Circuit Board: 步骤 7 中的图像 3，3

    • Remove the two 6mm screws at the base of the ring using a Phillips #0 screwdriver.

    • Pull towards the base of the controller to release the black wire from the connector on the circuit board.

    • Pull the ring apart from the rest of the controller.

    编辑

  9. HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement: 步骤 8 中的图像 1，3 HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement: 步骤 8 中的图像 2，3 HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement: 步骤 8 中的图像 3，3

    • Remove the two 3mm screws on the V-clip using a Phillips #00 screwdriver.

    • Remove the V-clip from the device.

    编辑

  10. HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement: 步骤 9 中的图像 1，3 HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement: 步骤 9 中的图像 2，3 HP Windows Mixed Reality Controllers TPC-Q044 Main Circuit Board Replacement: 步骤 9 中的图像 3，3

    • With the V-clip off of the controller, use a Phillips #00 screwdriver to remove the remaining 4mm screw.

    • Remove the circuit board.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

4等其他人完成本指南。

作者

与4其他贡献者

Eeshan Mishra

于01/24/19注册

424 声望

创作了4篇指南

徽章: 8

+ 5更多徽章

1指南评论

Awesome! But were do you get the components to replace from??

Since separate controllers are very difficult to find and expensive (You wont find Samsung ones) I will be interested to buy a few to do repairs to friends and so.

Baba Nam Kevalam - 回复

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 5

过去 30 天： 21

总计 2,202