跳转到主内容
  1. 这个步骤还没有翻译 帮忙翻译一下

    Separate the screen from the keyboard. Separate the screen from the keyboard.
    • Separate the screen from the keyboard.

  2. 这个步骤还没有翻译 帮忙翻译一下

    Loosen the adhesive under the gray plastic bar using a heat pad or a heat gun.
    • Loosen the adhesive under the gray plastic bar using a heat pad or a heat gun.

    • Remove the gray plastic bar after 5 minutes of light heat with tweezers by pulling up.

  3. 这个步骤还没有翻译 帮忙翻译一下

    Remove the 4 screws with a Phillips #0 screwdriver.
    • Remove the 4 screws with a Phillips #0 screwdriver.

    • These 4 screws have a diameter of 4.3 mm and a height of 3.7 mm.

  4. 这个步骤还没有翻译 帮忙翻译一下

    Remove the rubber stoppers at the top left and right with tweezers. Remove the screws  at the top and right with at Phillips #0 screwdriver.
    • Remove the rubber stoppers at the top left and right with tweezers.

    • Remove the screws at the top and right with at Phillips #0 screwdriver.

    • These two screws have a diameter of 5.3 mm and a height of 4.3 mm.

  5. 这个步骤还没有翻译 帮忙翻译一下

    Pry open the back case with a metal spudger. Then pry open the back layer with the metal spudger. Then pry open the back layer with the metal spudger.
    • Pry open the back case with a metal spudger.

    • Then pry open the back layer with the metal spudger.

  6. 这个步骤还没有翻译 帮忙翻译一下

    Fully take off the back panel by lifting up the panel. Fully take off the back panel by lifting up the panel.
    • Fully take off the back panel by lifting up the panel.

  7. 这个步骤还没有翻译 帮忙翻译一下

    Pop open the ribbon cable piece on the touch pad with the blue plastic spudger. Remove the ribbon cable with tweezers by pulling it out.
    • Pop open the ribbon cable piece on the touch pad with the blue plastic spudger.

    • Remove the ribbon cable with tweezers by pulling it out.

  8. 这个步骤还没有翻译 帮忙翻译一下

    Remove 4 screws with at Phillips #0 screwdriver. All 4 screws have a diameter of 4.3 mm and a height of 3.7 mm. Lift the tape shown with orange boxes with tweezers.
    • Remove 4 screws with at Phillips #0 screwdriver. All 4 screws have a diameter of 4.3 mm and a height of 3.7 mm.

    • Lift the tape shown with orange boxes with tweezers.

    • Remove metal bar with a blue spudger.

  9. 这个步骤还没有翻译 帮忙翻译一下

    Lift up the touch pad by the metal edge with a blue plastic spudger. Remove the touch pad from the computer. Remove the touch pad from the computer.
    • Lift up the touch pad by the metal edge with a blue plastic spudger.

    • Remove the touch pad from the computer.

终点

Cayla Skaggs

于2019年04月01日注册

337 信誉积分

创作了2篇指南

团队

IUPUI, Team S1-G4, Harley Spring 2019 IUPUI, Team S1-G4, Harley Spring 2019 的会员

IUPUI-HARLEY-S19S1G4

3 名成员

创作了3篇指南

0条评论

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 7

总计 423