跳转到主内容

简介

The hinge of the HP Pavilion X2 may need replacement if it is damaged, or the screen is unable to open properly. This guide shows how to disassemble the HP Pavilion X2 to allow for removal and replacement of the hinge, which connects the screen with the keyboard.

  1. Separate the screen from the keyboard. Separate the screen from the keyboard.
    • Separate the screen from the keyboard.

  2. Remove the grey rubber bar using plastic spudger or tweezers, exposing the four screw heads. The rubber bar is attached with an adhesive. A heat pad may be required to melt the adhesive and allow for easier removal.
    • Remove the grey rubber bar using plastic spudger or tweezers, exposing the four screw heads.

    • The rubber bar is attached with an adhesive. A heat pad may be required to melt the adhesive and allow for easier removal.

  3. Unscrew the four screws using the Phillips #0 screwdriver.
    • Unscrew the four screws using the Phillips #0 screwdriver.

    • All four of these screws have a diameter of 4.3 mm and a height of 3.7 mm.

  4. Remove the circular rubber tabs exposing the screw heads below. A heat pad may be required to melt the tab adhesive and allow for easier removal.
    • Remove the circular rubber tabs exposing the screw heads below.

    • A heat pad may be required to melt the tab adhesive and allow for easier removal.

    • Unscrew the two screws using the Phillips #0 screwdriver.

    • These two screws are 5.3 mm in diameter and 4.3 mm in height.

  5. Once all screws have been removed, gently pry open the back casing using a metal spudger. Be sure to use the spudger at the marked locations to avoid damage to the casing. Be sure to use the spudger at the marked locations to avoid damage to the casing.
    • Once all screws have been removed, gently pry open the back casing using a metal spudger.

    • Be sure to use the spudger at the marked locations to avoid damage to the casing.

  6. Completely remove the back casing. Completely remove the back casing.
    • Completely remove the back casing.

  7. Unscrew the four screws located at the marked locations using the Phillips #0 screwdriver.
    • Unscrew the four screws located at the marked locations using the Phillips #0 screwdriver.

    • All fours of these screws have a 7.0 mm diameter an a 2.5 mm height.

  8. Remove adhesive that secures the ribbon cable using tweezers.
    • Remove adhesive that secures the ribbon cable using tweezers.

  9. Using a plastic spudger, flip open the switch for the connection port, allowing the ribbon cable to be removed. Using a plastic spudger, flip open the switch for the connection port, allowing the ribbon cable to be removed. Using a plastic spudger, flip open the switch for the connection port, allowing the ribbon cable to be removed.
    • Using a plastic spudger, flip open the switch for the connection port, allowing the ribbon cable to be removed.

  10. Gently lift the hinge from the attachment points as shown in the picture. Tweezers can be also be used to ensure the ribbon cable does not get damaged in the process. The hinge can now be completely separated.
    • Gently lift the hinge from the attachment points as shown in the picture.

    • Tweezers can be also be used to ensure the ribbon cable does not get damaged in the process.

    • The hinge can now be completely separated.

结论

To reassemble your device, follow these instructions in reverse order.

Ajay Panuganti

于2019年04月01日注册

181 信誉积分

撰写一个指南

团队

IUPUI, Team S1-G4, Harley Spring 2019 IUPUI, Team S1-G4, Harley Spring 2019 的会员

IUPUI-HARLEY-S19S1G4

3 名成员

创作了3篇指南

添加评论

浏览统计数据:

过去的24小时: 1

过去的7天: 8

过去的30天: 23

总计 620