跳转到主内容

简介

This guide is for users who need to replace the cooling fan in their HP Pavilion 15-n232nr. The tools required are the spudger, screwdriver, and tweezers.

  1. Flip the laptop over. Flip the laptop over.
    • Flip the laptop over.

  2. Slide the battery locks towards the center of the laptop. The battery will detach automatically. Remove the battery by sliding it away from the laptop housing. Remove the battery by sliding it away from the laptop housing.
    • Slide the battery locks towards the center of the laptop. The battery will detach automatically.

    • Remove the battery by sliding it away from the laptop housing.

  3. Remove the 6 mm Phillips #1 screw securing the optical drive. Remove the 6 mm Phillips #1 screw securing the optical drive.
    • Remove the 6 mm Phillips #1 screw securing the optical drive.

  4. Use the iFixit opening tool to slide the optical drive away from the laptop housing. Use the iFixit opening tool to slide the optical drive away from the laptop housing.
    • Use the iFixit opening tool to slide the optical drive away from the laptop housing.

  5. Unscrew the 6 mm Phillips #1 screw securing the keyboard. Unscrew the 6 mm Phillips #1 screw securing the keyboard.
    • Unscrew the 6 mm Phillips #1 screw securing the keyboard.

  6. Flip the laptop to the front side and open it up. Flip the laptop to the front side and open it up.
    • Flip the laptop to the front side and open it up.

  7. Use the metal spudger to release the keyboard from the front panel. Use the metal spudger to release the keyboard from the front panel.
    • Use the metal spudger to release the keyboard from the front panel.

  8. Flip the keyboard out and locate the connector. Use the spudger to unhinge the the fastener and remove the connector. Keyboard should be completely detached after this step.
    • Flip the keyboard out and locate the connector.

    • Use the spudger to unhinge the the fastener and remove the connector.

    • Keyboard should be completely detached after this step.

  9. Loosen the two 6 mm Phillips #1 screws on the back panel. These screws do not detach from back panel.
    • Loosen the two 6 mm Phillips #1 screws on the back panel.

    • These screws do not detach from back panel.

  10. Use the iFixit opening tool to remove the back panel. Use the iFixit opening tool to remove the back panel.
    • Use the iFixit opening tool to remove the back panel.

  11. Release the clips securing the RAM by slightly bending them until the RAM is free. Release the clips securing the RAM by slightly bending them until the RAM is free.
    • Release the clips securing the RAM by slightly bending them until the RAM is free.

  12. The battery and optical drive should be removed at this point in the process. Remove the ten 6 mm Phillips #1 screws.
    • The battery and optical drive should be removed at this point in the process.

    • Remove the ten 6 mm Phillips #1 screws.

    • Remove the three 1 mm Phillips #000 screws.

  13. Remove the five 2.5mm Phillips #1 screws. Use the spudger to unhinge the cable connectors. Use tweezers to complete removal.
    • Remove the five 2.5mm Phillips #1 screws.

    • Use the spudger to unhinge the cable connectors. Use tweezers to complete removal.

  14. Carefully use the iFixit opening tool to release the front panel. Carefully use the iFixit opening tool to release the front panel. Carefully use the iFixit opening tool to release the front panel.
    • Carefully use the iFixit opening tool to release the front panel.

  15. Use the spudger to unhinge the daughterboard connector. Remove daughterboard connector. Remove daughterboard connector.
    • Use the spudger to unhinge the daughterboard connector.

    • Remove daughterboard connector.

  16. Remove the 2.5 mm Phillips #1 screw and remove the daughterboard
    • Remove the 2.5 mm Phillips #1 screw and remove the daughterboard

  17. Use the iFixit opening tool to remove the hard drive connector. Remove the hard drive by lifting the right side and pulling it out. Remove the hard drive by lifting the right side and pulling it out.
    • Use the iFixit opening tool to remove the hard drive connector.

    • Remove the hard drive by lifting the right side and pulling it out.

  18. Remove the four 6 mm Phillips #1 screws. Turn over the laptop to have easier access to the cooling fan. Turn over the laptop to have easier access to the cooling fan.
    • Remove the four 6 mm Phillips #1 screws.

    • Turn over the laptop to have easier access to the cooling fan.

  19. Unscrew the two 4 mm Phillips #1 screws. Disconnect the cord for the cooling fan. Carefully lift the cooling fan from the motherboard.
    • Unscrew the two 4 mm Phillips #1 screws.

    • Disconnect the cord for the cooling fan.

    • Carefully lift the cooling fan from the motherboard.

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

[deleted]

于2019年03月18日注册

262 信誉积分

创作了2篇指南

一条评论

Sehr gute Anleitung, Dank an Andrei Fendly

H. Hofmann

Helmut Hofmann - 回复

添加评论

浏览统计数据:

过去的24小时: 1

过去的7天: 3

过去的30天: 9

总计 380