修复你的物品 社区 商店

HP PSC 2355 Button Panel Replacement

简介

A defective button pad is is not difficult to replace with just a couple tools.

你所需要的

  1. HP PSC 2355 Button Panel Replacement, Scanner Lid: 步骤 1 中的图像 1，1

    • Grasp the scanner lid cover from the front of the device and lift lid all the way up until it stands on its own.

    编辑

  2. HP PSC 2355 Button Panel Replacement: 步骤 2 中的图像 1，1

    • With two hands, grasp the lid on both sides near the hinges and lift straight up to release the lid from each hinge.

    编辑

  3. HP PSC 2355 Button Panel Replacement, Button Panel: 步骤 3 中的图像 1，1

    • Once you have removed the scanner lid, locate the finger notch on inside the top left half of the bezel (control) panel.

    编辑

  4. HP PSC 2355 Button Panel Replacement: 步骤 4 中的图像 1，1

    • Place your index finger in the notch and lift up to unsnap the panel.

    • Set panel cover aside.

    编辑

  6. HP PSC 2355 Button Panel Replacement: 步骤 5 中的图像 1，1

    • Use a T9 torx screwdriver to remove the 0.9 cm screw.

    编辑

  7. HP PSC 2355 Button Panel Replacement: 步骤 6 中的图像 1，1

    • From the front of the printer, remove the button panel by pulling it towards you while slightly lifting it up.

    编辑

  8. HP PSC 2355 Button Panel Replacement: 步骤 7 中的图像 1，1

    • Disconnect the white ribbon cable by grasping it between your thumb and index finger.

    • Gently pull to release the ribbon from the green circuit board

    编辑

  9. HP PSC 2355 Button Panel Replacement: 步骤 8 中的图像 1，1

    • Next, use the flat end of a spudger to pry loose the flat ribbon computer cable by the plastic connection end and carefully separate it from the prongs on the button panel.

    • The entire button panel should now be completely disconnected from the printer.

    编辑

  10. HP PSC 2355 Button Panel Replacement: 步骤 9 中的图像 1，1

    • Lay the panel on a flat surface with the backside facing up.

    • Using a T9 torx screwdriver, remove all six 0.7 cm silver screws from the off-white plastic panel.

    编辑

  11. HP PSC 2355 Button Panel Replacement: 步骤 10 中的图像 1，1

    • Gently lift the button panel off the plastic backing with rubber button mat.

    编辑

  12. HP PSC 2355 Button Panel Replacement: 步骤 11 中的图像 1，1

    • Be careful not to lift out and lose the two clear plastic panel separators (these are not fastened to the panel but can easily fall out of the panel if tilted). These are two small plastic parts that sit near the top right and left portions of the panel.

    • Insert your new button panel. To reassemble your printer, follow these instructions in reverse order.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

2等其他人完成本指南。

作者

与3其他贡献者

Patricia

于01/23/14注册

143 声望

撰写一个指南

徽章: 7

+ 4更多徽章

团队

TheFixers TheFixers 的会员

Community

2 名成员

创作了1篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 0

过去 30 天： 1

总计 969