Introduction

The scanner head is necessary for copying and faxing. Follow the guide to replace this crucial part.

There is a hidden screw underneath the model sticker on the front panel. Peel the model sticker off the cover. This will expose the T10 screw securing the panel.
  • There is a hidden screw underneath the model sticker on the front panel.

  • Peel the model sticker off the cover.

  • This will expose the T10 screw securing the panel.

Add Comment

Remove the single 12mm-T10 screw securing the front panel to the printer body. Loosen the panel cover from the printer body. There is a ribbon cable connected to the backside of the cover. Disconnect the cable before separating the panel completely.
  • Remove the single 12mm-T10 screw securing the front panel to the printer body.

  • Loosen the panel cover from the printer body.

  • There is a ribbon cable connected to the backside of the cover. Disconnect the cable before separating the panel completely.

Add Comment

Gently remove the No-Fuss ribbon cable from the front panel. Gently remove the No-Fuss ribbon cable from the front panel. Gently remove the No-Fuss ribbon cable from the front panel.
  • Gently remove the No-Fuss ribbon cable from the front panel.

Add Comment

Remove the seven 8mm screws using the Torx T6 screwdriver. Remove the motherboard from the front-panel housing. The LCD display is on the opposite side.
  • Remove the seven 8mm screws using the Torx T6 screwdriver.

  • Remove the motherboard from the front-panel housing.

  • The LCD display is on the opposite side.

Add Comment

Lift the hood of the printer. Lift the hood of the printer. Lift the hood of the printer.
  • Lift the hood of the printer.

Add Comment

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Remove the two T10 11mm screws. Remove the two T10 11mm screws. Remove the two T10 11mm screws.
  • Remove the two T10 11mm screws.

Add Comment

Remove the panels covering the power brick and cord. Remove the panels covering the power brick and cord. Remove the panels covering the power brick and cord.
  • Remove the panels covering the power brick and cord.

Add Comment

Remove the cord from the power supply. Remove the cord from the power supply.
  • Remove the cord from the power supply.

Add Comment

Slide the power supply out from the chassis. The power supply is still attached; don't pull too quickly. The power supply is still attached; don't pull too quickly.
  • Slide the power supply out from the chassis.

  • The power supply is still attached; don't pull too quickly.

Add Comment

Remove final cable from power supply.
  • Remove final cable from power supply.

Add Comment

Remove eight T10 1mm screws from the top hood of the printer.
  • Remove eight T10 1mm screws from the top hood of the printer.

Add Comment

Use the nylon spudger to pry the tab. Lift up the entire panel. Lift up the entire panel.
  • Use the nylon spudger to pry the tab.

  • Lift up the entire panel.

Add Comment

Lift and flip the entire panel. Be aware of the scanner head attached to the panel. Be aware of the scanner head attached to the panel.
  • Lift and flip the entire panel.

  • Be aware of the scanner head attached to the panel.

Add Comment

Start with the scanner head in place. Unwind the ribbon from the track. Detach ribbon completely.
  • Start with the scanner head in place.

  • Unwind the ribbon from the track.

  • Detach ribbon completely.

Add Comment

Conclusion

To reassemble your device, follow these instructions in reverse order.

Maya Willis

Member since: 01/24/2018

340 Reputation

3 Guides authored

Team

Cal Poly, Team S18-G3, Livingston Winter 2018 Member of Cal Poly, Team S18-G3, Livingston Winter 2018

CPSU-LIVINGSTON-W18S18G3

4 Members

7 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 2

Past 30 Days: 9

All Time: 60