Skip to main content

介绍

The replacement for your device's motherboard requires a little extra effort than the other components in the device, but is still easily manageable with a soldering kit. With the little amount of desoldering required for this project, a YouTube video undergoing basic safety precautions and soldering kit use is recommended.

  1. Remove (2) screws (14 mm) with a PH1 screwdriver on the device.
    • Remove (2) screws (14 mm) with a PH1 screwdriver on the device.

    • There is one screw on the back left, and another just below it on the bottom of the device.

  2. Use a plastic spudger to remove the front preset selection buttons. We recommend you remove all of them for easier access.
    • Use a plastic spudger to remove the front preset selection buttons.

    • We recommend you remove all of them for easier access.

    • Gently reach underneath and pull off the mesh speaker cover. It only clips in so don't worry about breaking anything.

  3. Remove (4) screws (14 mm) with a PH1 screwdriver on the front panel by the speaker.
    • Remove (4) screws (14 mm) with a PH1 screwdriver on the front panel by the speaker.

    • Be careful with these screws, as they can be stripped easily.

  4. Android 维修工具包

    一个新的屏幕或电池就在一个套件之内。

    现在开始购物

    Android 维修工具包

    一个新的屏幕或电池就在一个套件之内。

    现在开始购物
  5. Move the metal spudger around the front panel to remove any adhesive attaching the front panel to the device.
    • Move the metal spudger around the front panel to remove any adhesive attaching the front panel to the device.

    • Pull apart the front panel from the device with help from the metal spudger.

  6. Detach a pin connector at the top of the device using a metal spudger to open up the inner components. Detach (4) pin connectors inside using a metal spudger to separate the front panel from the rest of the device. Detach (4) pin connectors inside using a metal spudger to separate the front panel from the rest of the device.
    • Detach a pin connector at the top of the device using a metal spudger to open up the inner components.

    • Detach (4) pin connectors inside using a metal spudger to separate the front panel from the rest of the device.

  7. Remove (10) screws (10 mm) with a PH1 screwdriver on the display board.
    • Remove (10) screws (10 mm) with a PH1 screwdriver on the display board.

  8. Remove the motherboard from the front panel.
    • Remove the motherboard from the front panel.

    • If motherboard is difficult to separate, DO NOT force it. Check to see if all the screws were removed and proceed to remove the motherboard gently.

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

Nathaniel Brabham

于2016年02月08日注册

395 Reputation

创作了3篇指南

Team

USF Tampa, Team 6-3, Eyestone Spring 2016 USF Tampa, Team 6-3, Eyestone Spring 2016 的会员

USFT-EYESTONE-S16S6G3

4 名成员

创作了8篇指南

One Comment

Nice guide. My Mondo Wi-Fi went flaky (read “died”) so I disassembled using this guide to check out the wi-fi adapter plugged into the internal USB port. Turned out the little adhesive they apply to keep the adapter in the USB port sort of flowed over the adapter. Cleaned the adapter and plugged into the USB port on the rear of the radio and I’m back with a working Mondo. Glad iFixit does more than just computers and phones and pads (though it seems the Mondo is really a little Linux box).

csiemen - 回复

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 5

Past 30 Days: 35

All Time: 2,378