修复你的物品 社区 商店

GoPro Hero 4 Black Charging Port Replacement

已存档的指南
本指南只作为历史记录保留。请使用指南的最新版本来进行维修。

你所需要的

  1. GoPro Hero 4 Black Charging Port Replacement, Charging Port: 步骤 1 中的图像 1，1

    • The first step to removing the faceplate is carefully moving the opening tool around the edge.

    • After loosening the clips on the edge, pull the faceplate off. Be aware that there is double-sided stick tape holding it on (indicated by the red arrow).

    翻译

  2. GoPro Hero 4 Black Charging Port Replacement: 步骤 2 中的图像 1，1

    • Remove the four Phillips #000 screws.

    • The screws circled in red are longer than the screw circled in orange.

    翻译

  3. GoPro Hero 4 Black Charging Port Replacement: 步骤 3 中的图像 1，1

    • Remove the camera and boards from the black plastic housing. You can use many tools to do this. We found that using the plastic opening tool may assist in the removal.

    翻译

  4. GoPro Hero 4 Black Charging Port Replacement: 步骤 4 中的图像 1，1

    • Remove the ribbon cable by simply pulling on it. This will remove it from its connection.

    • Push down on the three wires and the clip will disconnect from the motherboard.

    翻译

  6. GoPro Hero 4 Black Charging Port Replacement: 步骤 5 中的图像 1，1

    • Remove the four Phillips #000 screws.

    • Once the screws are removed and out of the way, gently remove the board. As you lift the board, the computer chip (outlined in orange) will separate from the motherboard.

    翻译

  7. GoPro Hero 4 Black Charging Port Replacement: 步骤 6 中的图像 1，1

    • Take your screwdriver with the PH000 Philips head attachment on it and remove the four screws outlined in red.

    • Just like before, just pull up on the ribbon strip and remove the connector from the motherboard.

    翻译

  8. GoPro Hero 4 Black Charging Port Replacement: 步骤 7 中的图像 1，1

    • Remove these two screws and remove the riser that is being held in by the screws.

    翻译

  9. GoPro Hero 4 Black Charging Port Replacement: 步骤 8 中的图像 1，1

    • Remove the screw holding the motherboard in place.

    • Do not attempt to remove the motherboard at this stage, as it is still attached by a ribbon cable.

    翻译

  10. GoPro Hero 4 Black Charging Port Replacement: 步骤 9 中的图像 1，1

    • At the top of the ribbon cable, there is a black clip that needs to be popped up.

    • You can use your finger to pop this up. But, a pair of needle nose tweezers might help.

    翻译

  11. GoPro Hero 4 Black Charging Port Replacement: 步骤 10 中的图像 1，1

    • Gently grab the ribbon with the needle nose tweezers and pull down. This will disconnect the ribbon from the connector.

    • Now, the motherboard can be removed. Due to the USB connector being on the motherboard, the entire board needs to be replaced.

    翻译
结论

To reassemble your device, follow these instructions in reverse order.

6等其他人完成本指南。

作者

与8其他贡献者

Jonathan Campbell

于09/29/15注册

830 声望

创作了3篇指南

徽章: 13

+ 10更多徽章

团队

IUPUI, Team 1-2, Hagerty Fall 2015 IUPUI, Team 1-2, Hagerty Fall 2015 的会员

IUPUI-HAGERTY-F15S1G2

3 名成员

创作了3篇指南

一条评论

got a part number for the USB? digikey?

hazakins - 回复

添加评论

浏览统计数据:

过去 24 小时： 1

过去 7 天： 1

过去 30 天： 4

总计 4,161