跳转到主内容
  1. Pull back on the tab on the back of GoPro to open the battery cover. Pull back on the tab on the back of GoPro to open the battery cover.
    • Pull back on the tab on the back of GoPro to open the battery cover.

  2. Pull the battery out using the tab.
    • Pull the battery out using the tab.

  3. Use the plastic opening tool to remove the faceplate. There is some adhesive and clips so be careful and the faceplate should pop right off.
    • Use the plastic opening tool to remove the faceplate.

    • There is some adhesive and clips so be careful and the faceplate should pop right off.

  4. Now that the faceplate is off, it is time to remove the 4 screws on each corner. Use the T4 tool bit from the iFixit toolkit in order to remove the 4 screws on each corner.
    • Now that the faceplate is off, it is time to remove the 4 screws on each corner.

    • Use the T4 tool bit from the iFixit toolkit in order to remove the 4 screws on each corner.

  5. PC 笔记本电池

    An easy fix for a big power boost.

    现在开始购物

    PC 笔记本电池

    An easy fix for a big power boost.

    现在开始购物
  6. Note: Make sure you remove the door cover of the USB, mini HDMI, and SD port before. Separating the motherboard will be easier. Using the plastic opening tool, slowly pry open the motherboard assembly.
    • Note: Make sure you remove the door cover of the USB, mini HDMI, and SD port before. Separating the motherboard will be easier.

    • Using the plastic opening tool, slowly pry open the motherboard assembly.

  7. Use the spudger to gently pry off the connector of the housing to the motherboard. You should now have the motherboard assembly and the housing separated.
    • Use the spudger to gently pry off the connector of the housing to the motherboard.

    • You should now have the motherboard assembly and the housing separated.

  8. Use the spudger to remove the heat shield tape and detach the image sensor from the motherboard. Using the T4 Torx toolbit, remove the 4 screws that connect the sensor to the lens. Remove the silver connector of the image sensor from the motherboard using the spudger to pry it off.
    • Use the spudger to remove the heat shield tape and detach the image sensor from the motherboard.

    • Using the T4 Torx toolbit, remove the 4 screws that connect the sensor to the lens.

    • Remove the silver connector of the image sensor from the motherboard using the spudger to pry it off.

  9. The media adapter is attached to the motherboard via 3 screws: x1 T4 Torx x2 Phillips #00
    • The media adapter is attached to the motherboard via 3 screws:

    • x1 T4 Torx

    • x2 Phillips #00

    • There's a little silver bracket that is held down by the Phillips #00 screw so be careful not to lose it.

    • With a little prying, use the spudger to detach the media adapter's connector from the motherboard.

  10. Use the spudger to lift the black tab up to unlock. Then remove LCD screen connector by sliding  out. Then remove LCD screen connector by sliding  out.
    • Use the spudger to lift the black tab up to unlock.

    • Then remove LCD screen connector by sliding out.

  11. Using the Phillips head bit, remove the silver screw near the top edge of the board. Separate the LCD assembly by pulling it away. You should have the bare motherboard! Separate the LCD assembly by pulling it away. You should have the bare motherboard!
    • Using the Phillips head bit, remove the silver screw near the top edge of the board.

    • Separate the LCD assembly by pulling it away. You should have the bare motherboard!

结论

To reassemble your device, follow these instructions in reverse order.

12等其他人完成本指南。

Brian Alvarez

于2015年04月02日注册

1,322 信誉积分

创作了6篇指南

团队

Cal Poly, Team 24-7, Lancaster Spring 2015 Cal Poly, Team 24-7, Lancaster Spring 2015 的会员

CPSU-LANCASTER-S15S24G7

3 名成员

创作了14篇指南

添加评论

浏览统计数据:

过去的24小时: 2

过去的7天: 17

过去的30天: 50

总计 6,426