跳转到主内容

简介

The image sensor is located behind the lens and is attached to the motherboard. Be careful in removing wiring from the motherboard, they are thin and small contacts and must be handled with care.

  1. GoPro Hero+ LCD Image Sensor Replacement, Back Panel: 步骤 1 中的图像 1,2 GoPro Hero+ LCD Image Sensor Replacement, Back Panel: 步骤 1 中的图像 2,2
    • Be sure to power off the GoPro before you start disassembly.

    • Pop up and pull back on the clip to remove the screen cover and expose the back panel with the touchscreen.

  2. GoPro Hero+ LCD Image Sensor Replacement: 步骤 2 中的图像 1,2 GoPro Hero+ LCD Image Sensor Replacement: 步骤 2 中的图像 2,2
    • Use the metal spudger to pry around the perimeter of the panel.

    • Pry the panel upwards by inserting the metal spudger into the corner crease between the panel and camera shell.

  3. GoPro Hero+ LCD Image Sensor Replacement: 步骤 3 中的图像 1,2 GoPro Hero+ LCD Image Sensor Replacement: 步骤 3 中的图像 2,2
    • Pry around the panel to ensure it is not attached to the device.

    • Move the panel to the side so you can access the internal components.

    • The panel is still attached to the rest of the device with a ribbon cable, so be sure to not tear or damage the cable.

  4. GoPro Hero+ LCD Image Sensor Replacement, Battery: 步骤 4 中的图像 1,1
    • Peel back the rear panel ribbon cable that is adhered to the battery until it is completely separated from the battery.

    • Be careful of metal contacts on strip; they can be sharp.

  5. GoPro Hero+ LCD Image Sensor Replacement: 步骤 5 中的图像 1,1
    • Using tweezers, peel off the copper tape on the right side of the battery.

  6. GoPro Hero+ LCD Image Sensor Replacement: 步骤 6 中的图像 1,2 GoPro Hero+ LCD Image Sensor Replacement: 步骤 6 中的图像 2,2
    • Place the plastic opening tool at one of the edges of the battery then pry until the battery is removed from the GoPro.

  7. GoPro Hero+ LCD Image Sensor Replacement: 步骤 7 中的图像 1,1
    • Use a pair of tweezers to disconnect the battery connector from the motherboard.

    • Gently pull the battery off the motherboard. Pulling vertically off the motherboard will give a clean release.

  8. GoPro Hero+ LCD Image Sensor Replacement, MicroSD/Micro USB Port Assembly: 步骤 8 中的图像 1,3 GoPro Hero+ LCD Image Sensor Replacement, MicroSD/Micro USB Port Assembly: 步骤 8 中的图像 2,3 GoPro Hero+ LCD Image Sensor Replacement, MicroSD/Micro USB Port Assembly: 步骤 8 中的图像 3,3
    • Remove the two 6 mm Phillips #00 screws.

    • Remove the single 4 mm Phillips #000 screws.

  9. GoPro Hero+ LCD Image Sensor Replacement: 步骤 9 中的图像 1,1
    • Remove the image sensor from the camera.

    • You do not have to unplug the black box to remove the USB/SD chip.

  10. GoPro Hero+ LCD Image Sensor Replacement: 步骤 10 中的图像 1,1
    • Grab the edge of the ribbon cable with the tweezers and gently pull until the cable is disconnected from the motherboard.

    • Be careful when removing the ribbon cable. You must pull gently or you can rip the ribbon off of its contacts.

  11. GoPro Hero+ LCD Image Sensor Replacement: 步骤 11 中的图像 1,1
    • Gently lift the microSD/Micro USB assembly up and out of the device.

  12. GoPro Hero+ LCD Image Sensor Replacement, Image Sensor: 步骤 12 中的图像 1,1
    • Use your fingers and gently pull out the sensor from the motherboard by slowly and gradually pulling up on the image sensor box.

    • Do not yank on the image sensor, it can rip out the wiring or damage the motherboard.

结论

To reassemble your device, follow these instructions in reverse order.

Matthew Tinkey

于2015年08月27日注册

862 声望分

创作了4篇指南

团队

USF Tampa, Team 2-4, Blackwell Fall 2015 USF Tampa, Team 2-4, Blackwell Fall 2015 的会员

USFT-BLACKWELL-F15S2G4

4 名成员

创作了18篇指南

0条评论

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 13

总计 1,317