修复你的物品 社区 商店

Giant Reign 2 Tube Replacement

简介

Installing a tube.

你所需要的

  1. Giant Reign 2 Tube Replacement, Hex Screws: 步骤 1 中的图像 1，1

    • Using the 4mm Allen wrench, partially unscrew the 4 (22mm) hex screws on the front of the axle casing to allow the axle to slide freely.

    编辑

  2. Giant Reign 2 Tube Replacement, Axle Screw: 步骤 2 中的图像 1，2 Giant Reign 2 Tube Replacement, Axle Screw: 步骤 2 中的图像 2，2

    • Using the 8mm Allen wrench, loosen the axle screw until 1/2 of the axle screw is visible.

    • Push the axle screw to reveal the axle rod on the other side.

    编辑

  3. Giant Reign 2 Tube Replacement: 步骤 3 中的图像 1，1

    • Using the Allen wrench, finish unscrewing the axle screw and pull it out.

    • Hold the wheel when pulling out the axle rod so that the bike does not fall.

    编辑

  4. Giant Reign 2 Tube Replacement, Front Wheel: 步骤 4 中的图像 1，1

    • Pull the wheel from the fork.

    编辑

  5. Giant Reign 2 Tube Replacement, Tube: 步骤 5 中的图像 1，1

    • Look at your tire and determine the correct tube size by locating the number (formated ## x #.##) on the wall of the tire.

    • Bike tubes come with one of two standard valve types: presta and schrader. These guides show the installation of a tube with a presta valve.

    编辑

  7. Giant Reign 2 Tube Replacement: 步骤 6 中的图像 1，3 Giant Reign 2 Tube Replacement: 步骤 6 中的图像 2，3 Giant Reign 2 Tube Replacement: 步骤 6 中的图像 3，3

    • Unscrew the cap covering the valve.

    • Remove the spacer that holds the valve in place against the rim of the wheel.

    • Open the valve by turning the nut and pressing the valve in to release air pressure from the tube.

    编辑

  8. Giant Reign 2 Tube Replacement: 步骤 7 中的图像 1，3 Giant Reign 2 Tube Replacement: 步骤 7 中的图像 2，3 Giant Reign 2 Tube Replacement: 步骤 7 中的图像 3，3

    • Slide the tire lever between the tire and the rim.

    • Push down on the tire lever until the edge of the tire is higher than the edge of the rim.

    • Insert a second tire lever adjacent to the first.

    • Slowly work one tire lever around the rim until the whole tire is loose.

    编辑

  9. Giant Reign 2 Tube Replacement: 步骤 8 中的图像 1，2 Giant Reign 2 Tube Replacement: 步骤 8 中的图像 2，2

    • Press the valve through the rim of the wheel.

    • Remove the tube from the tire.

    编辑

  10. Giant Reign 2 Tube Replacement: 步骤 9 中的图像 1，1

    • Partially inflate the tube.

    编辑

  11. Giant Reign 2 Tube Replacement: 步骤 10 中的图像 1，2 Giant Reign 2 Tube Replacement: 步骤 10 中的图像 2，2

    • Push the valve through the rim.

    • Push the tube into the tire all the way around the rim of the wheel.

    编辑

  12. Giant Reign 2 Tube Replacement: 步骤 11 中的图像 1，1

    • Push the bead of the tire back into place around the rim.

    • Make sure not to pinch the tube between the bead of the tire and the rim. Failure to do so may cause a pinch flat.

    编辑

  13. Giant Reign 2 Tube Replacement: 步骤 12 中的图像 1，1

    • Inflate the tube to the desired air pressure.

    • A suggested range of air pressure is located on the wall of the tire (formatted ##-##psi).

    编辑

  14. Giant Reign 2 Tube Replacement: 步骤 13 中的图像 1，2 Giant Reign 2 Tube Replacement: 步骤 13 中的图像 2，2

    • Close the valve and replace the cap.

    编辑
终点

另外一个人完成了本指南。

作者

与5其他贡献者

Sterling Grande

于10/08/12注册

148 声望

创作了4篇指南

徽章: 7

+ 4更多徽章

团队

Cal Poly, Team 9-14, Amido Fall 2012 Cal Poly, Team 9-14, Amido Fall 2012 的会员

CPSU-AMIDO-F12S9G14

4 名成员

创作了10篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 1

过去 30 天： 10

总计 2,845