修复你的物品 社区 商店

Garmin etrex Vista Cx Joy Stick Replacement

简介

This guide illustrates how to remove and replace the joy stick for this device.

你所需要的

  1. Garmin etrex Vista Cx Joy Stick Replacement, Battery: 步骤 1 中的图像 1，1

    • Place the device with the back cover facing up and the metal ring visible.

    编辑

  2. Garmin etrex Vista Cx Joy Stick Replacement: 步骤 2 中的图像 1，2 Garmin etrex Vista Cx Joy Stick Replacement: 步骤 2 中的图像 2，2

    • Lift the metal ring and rotate it counter-clockwise as shown. This will unlock the cover.

    编辑

  3. Garmin etrex Vista Cx Joy Stick Replacement: 步骤 3 中的图像 1，1

    • Remove the cover by lifting straight up to insert or remove 2 AA batteries.

    编辑

  5. Garmin etrex Vista Cx Joy Stick Replacement, Joy Stick: 步骤 4 中的图像 1，1

    • Remove the rubber grip that goes around the side of the device.

    编辑

  6. Garmin etrex Vista Cx Joy Stick Replacement: 步骤 5 中的图像 1，1

    • Underneath the rubber grip will also be a piece of tape over the plastic seam. You will need to take the metal spudger and break the tape along the seam.

    编辑

  7. Garmin etrex Vista Cx Joy Stick Replacement: 步骤 6 中的图像 1，1

    • Next you will have to use the plastic opening tool and pry at the bottom of the GPS. This will separate the front and the back of the device.

    编辑

  8. Garmin etrex Vista Cx Joy Stick Replacement: 步骤 7 中的图像 1，1

    • After the front and back are separated, there will be a small ribbon cable holding them together. You will need to pull straight back on the cable with fingers. This cable will pull straight out.

    编辑

  9. Garmin etrex Vista Cx Joy Stick Replacement: 步骤 8 中的图像 1，2 Garmin etrex Vista Cx Joy Stick Replacement: 步骤 8 中的图像 2，2

    • When looking at the motherboard you will notice there is one screw. To remove this, you will need a T4 bit in a nut driver. After you locate this screw you will need to remove it. The screw is 5 mm long.

    • After the screw is removed, the motherboard will lift out of the plastic case.

    编辑

  10. Garmin etrex Vista Cx Joy Stick Replacement: 步骤 9 中的图像 1，1

    • Locate the joystick on the motherboard.

    • Use a solder iron to remove the joystick from the motherboard.

    • In order to replace the joystick you have to purchase a new motherboard.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

2等其他人完成本指南。

作者

与3其他贡献者

Evan Borgman

于08/28/18注册

304 声望

创作了2篇指南

徽章: 5

+ 2更多徽章

团队

IUPUI, Team S1-G6, Arle Fall 2018 IUPUI, Team S1-G6, Arle Fall 2018 的会员

IUPUI-ARLE-F18S1G6

4 名成员

创作了3篇指南

一条评论

I took my etrex Venture apart following your process. I was able to get the rubber grip off without damaging it or it’s adhesive. I was also able to remove the adhesive sealing tape without damaging it as well. Allowing me to reassemble the entire thing using the original parts!!.

Also worth noting, in my case the joy stick worked in 3 of the 4 directions. It turns out that there is a small plastic sleeve that goes in the rubber joystick boot and onto the joystick when it’s all assembled. In my case this plastic sleeve was broken, not the actual joystick switch. I was able to use a small section of a Bic pen refill cut to the proper length. I had to go through several pen refills before I found a diameter that fit on the joystick switch properly. It now works like new!!

Robert Angelini - 回复

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 0

过去 30 天： 15

总计 1,399