Use the Phillips #00 screwdriver to remove the 7 screws on the sides of the camera: Four 3.95mm Phillips screws located on the bottom of the camera Two 3.95mm Phillips screws located on the right side of the camera
  • Use the Phillips #00 screwdriver to remove the 7 screws on the sides of the camera:

    • Four 3.95mm Phillips screws located on the bottom of the camera

    • Two 3.95mm Phillips screws located on the right side of the camera

    • One 3.95mm Phillips screw located on the left side of the camera

添加评论

Slide open the battery compartment cover with your thumb.
  • Slide open the battery compartment cover with your thumb.

添加评论

Wedge the edge of the spudger between the front and back case, near the corner of the flash. Carefully run the spudger along the right edge of the camera, creating an opening. Insert the spudger into the left side of the camera, above the screwhole. Then carefully run it along this edge.
  • Wedge the edge of the spudger between the front and back case, near the corner of the flash.

  • Carefully run the spudger along the right edge of the camera, creating an opening.

  • Insert the spudger into the left side of the camera, above the screwhole. Then carefully run it along this edge.

添加评论

Watch out for the orange ribbon that is still attached to the back cover when you lift it up. It is very delicate and might rip. Slowly lift the back cover straight up, lightly jiggling it if necessary.
  • Watch out for the orange ribbon that is still attached to the back cover when you lift it up. It is very delicate and might rip.

  • Slowly lift the back cover straight up, lightly jiggling it if necessary.

  • Remove the battery compartment cover.

添加评论

Mac RAM 套件
加速你的Mac。充分利用它的内存。
Mac RAM 套件
从Mac中清理出更多内存。
Gently insert the spudger under the clip holding the orange ribbon. The clip should lift up and the ribbon will slide out.
  • Gently insert the spudger under the clip holding the orange ribbon. The clip should lift up and the ribbon will slide out.

  • This step will free the back cover from the rest of the camera.

添加评论

Pull gently when removing the speaker so you don't rip the wire attached to it.
  • Pull gently when removing the speaker so you don't rip the wire attached to it.

  • Use the tweezers to grab the speaker (located on left side of the camera) and pull straight up.

  • The speaker will still be connected to the motherboard, but it will not be attached to the front case.

添加评论

Use the tweezers to pull gently on the small orange ribbon, located in upper left hand corner near the flash, to remove the square insert.
  • Use the tweezers to pull gently on the small orange ribbon, located in upper left hand corner near the flash, to remove the square insert.

添加评论

Use your fingers to slowly pull the flash straight up.
  • Use your fingers to slowly pull the flash straight up.

  • The step may take a little jiggling.

添加评论

Do not fully separate the motherboard unit from the front cover. There is still a ribbon attached and it will rip. Slightly separate the front cover from the motherboard unit (which consists of the motherboard, speaker, screen, and battery compartment).
  • Do not fully separate the motherboard unit from the front cover. There is still a ribbon attached and it will rip.

  • Slightly separate the front cover from the motherboard unit (which consists of the motherboard, speaker, screen, and battery compartment).

  • Rotate the bottom portion of the motherboard unit (the screen and battery compartment) over the lens unit.

添加评论

Use your fingers to remove the tripod mount.
  • Use your fingers to remove the tripod mount.

添加评论

Be gentle when undoing the ribbon clips. They break easily. Gently stick the spudger under the ribbon clips and lift them up. Use the tweezers to pull both ribbons out of the ribbon clips.
  • Be gentle when undoing the ribbon clips. They break easily.

  • Gently stick the spudger under the ribbon clips and lift them up.

  • Use the tweezers to pull both ribbons out of the ribbon clips.

  • The motherboard unit should now be free from the rest of the camera.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

Sarthak Patel

于2012年04月03日注册

1 信誉积分

创作了2篇指南

团队

Cal Poly, Team 14-8, Forte Spring 2012 Cal Poly, Team 14-8, Forte Spring 2012 的会员

CPSU-FORTE-S12S14G8

5 名成员

创作了8篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 2

过去的30天: 3

总计 644