Remove the batteries from the camera to prevent danger of electric shock.
  • Remove the batteries from the camera to prevent danger of electric shock.

添加评论

Locate all five screws on the camera. Then proceed to remove all the screws. Locate all five screws on the camera. Then proceed to remove all the screws. Locate all five screws on the camera. Then proceed to remove all the screws.
  • Locate all five screws on the camera. Then proceed to remove all the screws.

添加评论

Beware, if your screwdriver does not fit properly, you may damage the screws' heads.
  • Beware, if your screwdriver does not fit properly, you may damage the screws' heads.

  • If your screwdriver does not fit, or you do not have the proper one, you can use a hot glue gun to fix the screwdriver to the head of the screw. Wait for it to harden slightly, and then try to remove the screws.

添加评论

Remove outer case.  Pull the back away from the main body of the camera. Remove outer case.  Pull the back away from the main body of the camera.
  • Remove outer case. Pull the back away from the main body of the camera.

添加评论

Locate the LCD screen and anchoring screw.
  • Locate the LCD screen and anchoring screw.

  • Remove screw.

添加评论

Carefully pull the LCD screen away from the board it is connected to.
  • Carefully pull the LCD screen away from the board it is connected to.

添加评论

Push both blue switches away from the holding device to unleach lcd ribbon.
  • Push both blue switches away from the holding device to unleach lcd ribbon.

  • Be careful when removing ribbon. If you damage it, you will need to replace it as well.

添加评论

Carefully detach the ribbon from where it was connected by the blue pins.
  • Carefully detach the ribbon from where it was connected by the blue pins.

添加评论

Now that everything has been disconnected from the board, remove LCD screen.
  • Now that everything has been disconnected from the board, remove LCD screen.

添加评论

Remove the two screws holding the circuit board down.
  • Remove the two screws holding the circuit board down.

添加评论

Remove black sticky tape from circuit board and camera case. Remove black sticky tape from circuit board and camera case.
  • Remove black sticky tape from circuit board and camera case.

添加评论

Gently pull the circuit board away from the front side of the camera. Be careful when removing assembly as to not break any solder leads or damage lens assembly.
  • Gently pull the circuit board away from the front side of the camera.

  • Be careful when removing assembly as to not break any solder leads or damage lens assembly.

添加评论

Remove the logic board by pulling straight away from assembly. Remove the logic board by pulling straight away from assembly.
  • Remove the logic board by pulling straight away from assembly.

添加评论

Locate the flash unit of the camera.  It includes the camera's flash and a capacitor.
  • Locate the flash unit of the camera. It includes the camera's flash and a capacitor.

添加评论

Unsolder the flash unit at it's three points. Be careful not to damage the circuit board or surrounding parts with the solder iron.
  • Unsolder the flash unit at it's three points.

  • Be careful not to damage the circuit board or surrounding parts with the solder iron.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

Cody

于2010年04月18日注册

47 信誉积分

创作了4篇指南

团队

Cal Poly, Team 7-11, Maness Spring 2010 Cal Poly, Team 7-11, Maness Spring 2010 的会员

CPSU-MANESS-S10S7G11

3 名成员

创作了4篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 3

总计 3,614