跳转到主内容
  1. Be sure to unplug the device before proceeding.
    • Be sure to unplug the device before proceeding.

    • Use a Phillips #0 screwdriver to remove the four 21.7mm screws holding the back panel to the frame.

  2. Once the screws are out, use a plastic opening tool or spudger to pry the top of the back panel open. There may be some resistance, but it will eventually pry loose.
    • Once the screws are out, use a plastic opening tool or spudger to pry the top of the back panel open. There may be some resistance, but it will eventually pry loose.

  3. Once the top is separated, use your hand to remove the back panel from the unit.
    • Once the top is separated, use your hand to remove the back panel from the unit.

  4. There will be two black wires connecting the top mounting bracket to the reverb box at the bottom of the unit. Label the wires to prevent crossing upon re-installation, then unplug the wires from the reverb box. There will be two black wires connecting the top mounting bracket to the reverb box at the bottom of the unit. Label the wires to prevent crossing upon re-installation, then unplug the wires from the reverb box.
    • There will be two black wires connecting the top mounting bracket to the reverb box at the bottom of the unit. Label the wires to prevent crossing upon re-installation, then unplug the wires from the reverb box.

  5. iPhone X Fix Kits

    Warranty up? No worries, we’ve got the fix.

    现在开始购物

    iPhone X Fix Kits

    Warranty up? No worries, we’ve got the fix.

    现在开始购物
  6. Label and unplug the two red wires connecting the mounting bracket to the speaker by pulling them off the nodes.
    • Label and unplug the two red wires connecting the mounting bracket to the speaker by pulling them off the nodes.

  7. Use a Phillips #1 screwdriver to unscrew the four 36.4 mm screws holding the mounting bracket to the top of the amp. Use a Phillips #1 screwdriver to unscrew the four 36.4 mm screws holding the mounting bracket to the top of the amp. Use a Phillips #1 screwdriver to unscrew the four 36.4 mm screws holding the mounting bracket to the top of the amp.
    • Use a Phillips #1 screwdriver to unscrew the four 36.4 mm screws holding the mounting bracket to the top of the amp.

  8. Pull the mounting bracket free from the frame. It may be wedged in very snug, in which case, use a plastic opening tool/spudger to pry it loose from the front. Pull the mounting bracket free from the frame. It may be wedged in very snug, in which case, use a plastic opening tool/spudger to pry it loose from the front. Pull the mounting bracket free from the frame. It may be wedged in very snug, in which case, use a plastic opening tool/spudger to pry it loose from the front.
    • Pull the mounting bracket free from the frame. It may be wedged in very snug, in which case, use a plastic opening tool/spudger to pry it loose from the front.

  9. Mark, make note of, or remember the arrangement of the wires. Remove the four female disconnected terminals from the switch terminals.
    • Mark, make note of, or remember the arrangement of the wires.

    • Remove the four female disconnected terminals from the switch terminals.

  10. Using the flat end of a spudger, push in one of the wedged locking clips. Partially tilt the switch box so that clip is held down. Repeat for the other side of the switch
    • Using the flat end of a spudger, push in one of the wedged locking clips.

    • Partially tilt the switch box so that clip is held down.

    • Repeat for the other side of the switch

  11. Be sure that both locking clips are pressed through the opening. This may take a few tries. Gently remove the switch.
    • Be sure that both locking clips are pressed through the opening. This may take a few tries.

    • Gently remove the switch.

结论

Once the old power switch is removed, install the new one by following the guide in reverse.

另外一个人完成了本指南。

Greg Sawers

于2012年09月27日注册

79 信誉积分

创作了3篇指南

团队

Cal Poly, Team 24-30, Regan Fall 2012 Cal Poly, Team 24-30, Regan Fall 2012 的会员

CPSU-REGAN-F12S24G30

5 名成员

创作了7篇指南

添加评论

浏览统计数据:

过去的24小时: 1

过去的7天: 7

过去的30天: 34

总计 5,637