简介

This guide shows how to remove the paper eject frame assembly Constant paper jams might be caused by a faulty paper eject frame assembly. This process requires the knowledge of how to use basic tools.

Turn off the printer.
  • Turn off the printer.

  • Disconnect all data connections coming into the printer such as USB, networkd cables, firewire, etc. as well as removing the power cord.

添加评论

Locate the IEEE cover in  the back. Gently slide cover to the right to unlatch then pull to remove it.
  • Locate the IEEE cover in the back.

  • Gently slide cover to the right to unlatch then pull to remove it.

添加评论

Using a #2 Phillips screwdriver, remove the four 10mm screws shown. Remove the 6mm screw that holds the rear housing in place.
  • Using a #2 Phillips screwdriver, remove the four 10mm screws shown.

  • Remove the 6mm screw that holds the rear housing in place.

添加评论

Remove the rear housing by pulling it backwards. Remove the rear housing by pulling it backwards.
  • Remove the rear housing by pulling it backwards.

添加评论

Insert the flathead screwdriver or plastic pry tool into the cutouts of the lower housing. Release the two tabs of the side housing by lifting the tool in an upward motion Remove the side housing by pulling it outwards.
  • Insert the flathead screwdriver or plastic pry tool into the cutouts of the lower housing.

  • Release the two tabs of the side housing by lifting the tool in an upward motion

  • Remove the side housing by pulling it outwards.

添加评论

Both side housings are attached by the same type of mechanism. Using the same method, remove the other side housing.
  • Both side housings are attached by the same type of mechanism.

  • Using the same method, remove the other side housing.

添加评论

Lift the paper support. Open the printer cover and front cover. Open the printer cover and front cover.
  • Lift the paper support.

  • Open the printer cover and front cover.

添加评论

Remove the four 10 mm Phillips #2 screws from the sides of the printer. Remove the three 6mm Phillips #2 screws. Remove the three 6mm Phillips #2 screws.
  • Remove the four 10 mm Phillips #2 screws from the sides of the printer.

  • Remove the three 6mm Phillips #2 screws.

添加评论

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Detach the tabs from the pins on each side by pulling it outwards. Detach the tabs from the pins on each side by pulling it outwards.
  • Detach the tabs from the pins on each side by pulling it outwards.

添加评论

Remove the two 10 mm Phillips #2 screws on the front of the printer. Remove the two 10 mm Phillips #2 screws on the front of the printer.
  • Remove the two 10 mm Phillips #2 screws on the front of the printer.

添加评论

Disconnect the cable on the side by carefully pulling it outwards. You may need to gently rock the cable up and down while pulling. You may need to gently rock the cable up and down while pulling.
  • Disconnect the cable on the side by carefully pulling it outwards.

  • You may need to gently rock the cable up and down while pulling.

添加评论

Remove the upper housing by lifting it upwards. It's easier to lift  the housing by gripping it from the bottom.
  • Remove the upper housing by lifting it upwards.

  • It's easier to lift the housing by gripping it from the bottom.

添加评论

Hold the ink tube and draw out the waste ink tube by pulling on both tubes in opposite directions. Hold the ink tube and draw out the waste ink tube by pulling on both tubes in opposite directions.
  • Hold the ink tube and draw out the waste ink tube by pulling on both tubes in opposite directions.

添加评论

Remove the acetate tape that secure the connector cable. Remove the acetate tape that secure the connector cable.
  • Remove the acetate tape that secure the connector cable.

添加评论

There are six screws that secure the printer mechanism. Using the #2 Phillips screwdriver, remove the three 10mm screws shown. Using the #2 Phillips screwdriver, remove the three 10mm screws shown.
  • There are six screws that secure the printer mechanism.

  • Using the #2 Phillips screwdriver, remove the three 10mm screws shown.

添加评论

Using the #2 Phillips screwdriver, remove the last three 10mm screws securing the printer mechanism. Using the #2 Phillips screwdriver, remove the last three 10mm screws securing the printer mechanism. Using the #2 Phillips screwdriver, remove the last three 10mm screws securing the printer mechanism.
  • Using the #2 Phillips screwdriver, remove the last three 10mm screws securing the printer mechanism.

添加评论

Remove printer mechanism from lower housing by holding the handles and lifting it upwards. Remove printer mechanism from lower housing by holding the handles and lifting it upwards.
  • Remove printer mechanism from lower housing by holding the handles and lifting it upwards.

添加评论

Remove the CD-R unit housing by releasing the two attaching points to the tray base. Pull it outwards diagonally one side at a time. Pull it outwards diagonally one side at a time.
  • Remove the CD-R unit housing by releasing the two attaching points to the tray base.

  • Pull it outwards diagonally one side at a time.

添加评论

Remove the left frame support plate by removing the two 6mm screws that secure it. Pull it out by hand to free it. Pull it out by hand to free it.
  • Remove the left frame support plate by removing the two 6mm screws that secure it.

  • Pull it out by hand to free it.

添加评论

Using the #2 Phillips screwdriver, remove the four 6mm screws. Remove the two 8mm screws.
  • Using the #2 Phillips screwdriver, remove the four 6mm screws.

  • Remove the two 8mm screws.

  • The screws are located on the lower sections of the printer.

添加评论

Two guide pins secure the paper EJ assy in place. Remove the two guide pins on the CD/DVD tray base by pulling each pin outward. Remove the two guide pins on the CD/DVD tray base by pulling each pin outward.
  • Two guide pins secure the paper EJ assy in place.

  • Remove the two guide pins on the CD/DVD tray base by pulling each pin outward.

添加评论

Remove the paper EJ frame assy by pulling the it towards you. Remove the paper EJ frame assy by pulling the it towards you.
  • Remove the paper EJ frame assy by pulling the it towards you.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

25等其他人完成本指南。

Larry Huang

于2011年10月12日注册

686 信誉积分

创作了4篇指南

团队

Cal Poly, Team 17-11, Regan Fall 2011 Cal Poly, Team 17-11, Regan Fall 2011 的会员

CPSU-REGAN-F11S17G11

4 名成员

创作了6篇指南

添加评论

浏览统计数据:

过去的24小时: 3

过去的7天: 19

过去的30天: 107

总计 11,669