简介

To get to the inside parts of the printer, the housing components must come off.

Turn off the printer.
  • Turn off the printer.

  • Disconnect all data connections coming into the printer such as USB, networkd cables, firewire, etc. as well as removing the power cord.

添加评论

Locate the IEEE cover in  the back. Gently slide cover to the right to unlatch then pull to remove it.
  • Locate the IEEE cover in the back.

  • Gently slide cover to the right to unlatch then pull to remove it.

添加评论

Using a #2 Phillips screwdriver, remove the four 10mm screws shown. Remove the 6mm screw that holds the rear housing in place.
  • Using a #2 Phillips screwdriver, remove the four 10mm screws shown.

  • Remove the 6mm screw that holds the rear housing in place.

添加评论

Remove the rear housing by pulling it backwards. Remove the rear housing by pulling it backwards.
  • Remove the rear housing by pulling it backwards.

添加评论

Mac RAM 套件
加速你的Mac。充分利用它的内存。
Mac RAM 套件
从Mac中清理出更多内存。
Insert the flathead screwdriver or plastic pry tool into the cutouts of the lower housing. Release the two tabs of the side housing by lifting the tool in an upward motion Remove the side housing by pulling it outwards.
  • Insert the flathead screwdriver or plastic pry tool into the cutouts of the lower housing.

  • Release the two tabs of the side housing by lifting the tool in an upward motion

  • Remove the side housing by pulling it outwards.

添加评论

Both side housings are attached by the same type of mechanism. Using the same method, remove the other side housing.
  • Both side housings are attached by the same type of mechanism.

  • Using the same method, remove the other side housing.

添加评论

Lift the paper support. Open the printer cover and front cover. Open the printer cover and front cover.
  • Lift the paper support.

  • Open the printer cover and front cover.

添加评论

Remove the four 10 mm Phillips #2 screws from the sides of the printer. Remove the three 6mm Phillips #2 screws. Remove the three 6mm Phillips #2 screws.
  • Remove the four 10 mm Phillips #2 screws from the sides of the printer.

  • Remove the three 6mm Phillips #2 screws.

添加评论

Detach the tabs from the pins on each side by pulling it outwards. Detach the tabs from the pins on each side by pulling it outwards.
  • Detach the tabs from the pins on each side by pulling it outwards.

添加评论

Remove the two 10 mm Phillips #2 screws on the front of the printer. Remove the two 10 mm Phillips #2 screws on the front of the printer.
  • Remove the two 10 mm Phillips #2 screws on the front of the printer.

添加评论

Disconnect the cable on the side by carefully pulling it outwards. You may need to gently rock the cable up and down while pulling. You may need to gently rock the cable up and down while pulling.
  • Disconnect the cable on the side by carefully pulling it outwards.

  • You may need to gently rock the cable up and down while pulling.

添加评论

Remove the upper housing by lifting it upwards. It's easier to lift  the housing by gripping it from the bottom.
  • Remove the upper housing by lifting it upwards.

  • It's easier to lift the housing by gripping it from the bottom.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

5等其他人完成本指南。

Larry Huang

于2011年10月12日注册

686 信誉积分

创作了4篇指南

团队

Cal Poly, Team 17-11, Regan Fall 2011 Cal Poly, Team 17-11, Regan Fall 2011 的会员

CPSU-REGAN-F11S17G11

4 名成员

创作了6篇指南

Thank you so much, Larry! I am repurposing my 1400 for sublimation printing and need to get the print head a little easier than standard methods! Much appreciated!

ryan Caputo - 回复

添加评论

浏览统计数据:

过去的24小时: 3

过去的7天: 3

过去的30天: 22

总计 5,316