简介

Outline what you are going to teach someone how to do.

  1. Turn off the camera.
    • Turn off the camera.

      • Locate the power switch on the front of the camera below the camera lens.

      • Slide the switch to the off position.

    添加评论

  2. Locate the 3 screws that hold the back cover to the camera.
    • Locate the 3 screws that hold the back cover to the camera.

      • One screw is located on the film opener side of the camera.

      • The other screws are located on the opposite side of the camera.

    添加评论

    • Use the Phillips #00 Precision Screwdriver and remove the screws on the back cover.

    添加评论

    • Open the film door to remove the back cover.

      • Slide the film door lever to the left until the film door opens.

    添加评论

    • Use a plastic opening tool to pry the case open until a small gap is present.

      • Repeat this process at the top and bottom of the film door to loosen it.

    添加评论

    • Grab the top and bottom of the case firmly as shown.

      • Gently remove the back of the camera case with a slight twisting motion.

    添加评论

  3. 订单满 $20 免运费
    结账时使用优惠码 BLUEANDBLACK
    订单满 $20 免运费
    使用优惠码 BLUEANDBLACK
    • Locate the 3 screws on the camera that hold the front cover of the camera to the camera body.

      • The first 2 are located on the bottom of the camera.

      • The last screw is located behind the flash module.

        • Turn the camera on, and raise the flash module to locate the flash module screw.

    添加评论

    • Remove the 2 screws at the base of the camera housing.

      • Use the Phillips #00 Precision Screwdriver and remove the screws.

      • Repeat this process for the screw behind the flash module.

    添加评论

    • Remove the screw located under the flash module using the Phillips #00 Precision Screwdriver.

    添加评论

    • Remove the flash cover.

      • Remove the flash module by twisting it up and outward of the camera housing.

      • The cover can now be be removed.

    添加评论

    • Remove the film door lever.

      • Remove the screw holding the film lever in place by using a Phillips #00 Precision Screwdriver.

      • Using a plastic opening tool, gently pry the switch upwards to remove it.

    添加评论

    • Open the battery door by pushing the lever towards the arrow indicated.

    添加评论

    • Remove the front cover.

      • Insert your thumb in the film hole and gently pry the bottom loose.

      • Once the front is loose, gently pull it out.

    添加评论

    • Locate the 3 screws on the top of the camera.

      • These will be removed in the next step.

    添加评论

    • Remove the 3 screws using the Phillips #00 Precision Screwdriver.

    添加评论

    • Remove the LCD.

      • Gently pry the LCD and plastic bezel upward with a plastic opening tool.

      • Remove LCD and replace as needed.

    添加评论

结论

To reassemble your device, follow these instructions in reverse order.

David Cottrell

于2011年10月04日注册

58 信誉积分

创作了5篇指南

团队

UW Stout, Team 1-2, Zhou Fall 2011 UW Stout, Team 1-2, Zhou Fall 2011 的会员

UWSTOUT-ZHOU-F11S1G2

4 名成员

创作了5篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 2

总计 678