修复你的物品 社区 商店

Disassembling Insignia Flex 8 Circuit Board

简介

This guide should be completed before starting the other guides.

你所需要的

  1. Disassembling Insignia Flex 8 Circuit Board, Circuit Board: 步骤 1 中的图像 1，1

    • Turn off the power to your tablet to avoid injury.

    • Position the tablet so that the screen is face down and the power button is located in the upper left hand corner.

    • Hold down the power button for five seconds until the tablet powers down.

    编辑

  2. Disassembling Insignia Flex 8 Circuit Board: 步骤 2 中的图像 1，2 Disassembling Insignia Flex 8 Circuit Board: 步骤 2 中的图像 2，2

    • Remove the back casing from the screen by sliding a credit card or a similarly thin but firm object in between the casing and the screen.

    • You may need to use a spudger to initially create separation between the screen and the casing.

    • Run this object around the perimeter of the tablet until there is separation between the casing and the screen.

    • Remove the back casing and set aside.

    编辑

  3. Disassembling Insignia Flex 8 Circuit Board: 步骤 3 中的图像 1，2 Disassembling Insignia Flex 8 Circuit Board: 步骤 3 中的图像 2，2

    • Peel tape off of ribbon connectors. Starting at the power button, work clockwise around the tablet.

    编辑

  4. Disassembling Insignia Flex 8 Circuit Board: 步骤 4 中的图像 1，3 Disassembling Insignia Flex 8 Circuit Board: 步骤 4 中的图像 2，3 Disassembling Insignia Flex 8 Circuit Board: 步骤 4 中的图像 3，3

    • To remove the camera ribbon cable, lift the flap using a spudger.

    • Pull the ribbon directly back to release it.

    编辑

  6. Disassembling Insignia Flex 8 Circuit Board: 步骤 5 中的图像 1，3 Disassembling Insignia Flex 8 Circuit Board: 步骤 5 中的图像 2，3 Disassembling Insignia Flex 8 Circuit Board: 步骤 5 中的图像 3，3

    • Remove the second ribbon cable by prying up the black flap using a spudger.

    • Pull the ribbon cable horizontally directly away from the battery.

    编辑

  7. Disassembling Insignia Flex 8 Circuit Board: 步骤 6 中的图像 1，3 Disassembling Insignia Flex 8 Circuit Board: 步骤 6 中的图像 2，3 Disassembling Insignia Flex 8 Circuit Board: 步骤 6 中的图像 3，3

    • Remove the final ribbon cable by pulling back the two black tabs on either side of the ribbon cable.

    • Pull the ribbon horizontally directly away from the battery.

    编辑

  8. Disassembling Insignia Flex 8 Circuit Board: 步骤 7 中的图像 1，2 Disassembling Insignia Flex 8 Circuit Board: 步骤 7 中的图像 2，2

    • Unscrew the thirteen 4.75mm screws around the perimeter of the tablet using a PH 00 screwdriver.

    编辑

  9. Disassembling Insignia Flex 8 Circuit Board: 步骤 8 中的图像 1，2 Disassembling Insignia Flex 8 Circuit Board: 步骤 8 中的图像 2，2

    • Unscrew the four 3.75mm screws and plastic washers using a PH 00 screwdriver.

    • Lift up the circuit board.

    编辑

  10. Disassembling Insignia Flex 8 Circuit Board: 步骤 9 中的图像 1，1

    • Unscrew the final two screws that were underneath the circuit board.

    • These screws are near the charging port and USB adapter.

    • These screws are also 3.75mm and can be interchanged with the second set of screws only.

    编辑

  11. Disassembling Insignia Flex 8 Circuit Board: 步骤 10 中的图像 1，1

    • Lift the circuit board and black internal mounting piece away from the screen.

    • Set the circuit board aside.

    • Be careful of the soldered antenna as you separate the pieces.

    • Be careful of the soldered ribbon that is connected to the power source. This ribbon is fragile.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

2等其他人完成本指南。

作者

与2其他贡献者

Tyler Tyrrell

于03/11/15注册

890 声望

创作了4篇指南

徽章: 17

+ 14更多徽章

团队

Colorado Springs, Team 5-5, Panko Spring 2015 Colorado Springs, Team 5-5, Panko Spring 2015 的会员

UCCS-PANKO-S15S5G5

3 名成员

创作了12篇指南

2条评论

Whwre can i buy the new screen

Emmanuel - 回复

I don’t see the ssd, and way to upgrade the internal sad had?

William Henderson - 回复

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 3

过去 30 天： 6

总计 4,903