1. Locate and remove the 14.5 mm Phillips #1 screw on the bottom of the fan base.
    • Locate and remove the 14.5 mm Phillips #1 screw on the bottom of the fan base.

  2. Locate the gray base support release tabs found on either side pictured in the first image. There are release tabs on each side of the base.
    • Locate the gray base support release tabs found on either side pictured in the first image.

      • There are release tabs on each side of the base.

    • Press both release tabs in with the tip of your fingers and pull the gray base support until the tabs are cleared.

  3. Continue removing the gray base support by pressing your thumb into the circular opening in the base and pulling with your figures on the back side.
    • Continue removing the gray base support by pressing your thumb into the circular opening in the base and pulling with your figures on the back side.

    • Notice that on the internal front tip of the base there is a tab. Because of this tab the back end will pivot off at that point.

  4. 所有超过US$100.00或包含 Pro Tech工具包的订单免费送货!

    浏览我们的商店

    善于维修,即天赋异禀。

    与 #ImAGenius 分享您的维修故事

    我们都是天才

    与 #ImAGenius 分享您的维修故事

  5. After the base has separated more it will be easy to fully remove it. Continue pulling the back edge of the gray base support, rotating it around the front tab until it comes off completely.
    • After the base has separated more it will be easy to fully remove it. Continue pulling the back edge of the gray base support, rotating it around the front tab until it comes off completely.

  6. Remove the following five 14.5 mm Phillips #1 screws found on the bottom.
    • Remove the following five 14.5 mm Phillips #1 screws found on the bottom.

      • All of the screws are recessed by 17.5 mm, so ensure your screwdriver can reach that far.

  7. Once all five screws have been removed the base cover should fall right off with out any effort.
    • Once all five screws have been removed the base cover should fall right off with out any effort.

    • When putting the base cover back on; be careful to make sure that none of the wires are pinched.

  8. Remove the two 15 mm Phillips screws on the retention plate.
    • Remove the two 15 mm Phillips screws on the retention plate.

    • The tan retention plate will fall off once the screws are removed.

  9. Take the 1.5 mm Flathead Screwdriver, or any thin elongated tool that fits into the semi-circular holes along side the AC power cord white wire. Press into the hole gently to release the grip on the wire.
    • Take the 1.5 mm Flathead Screwdriver, or any thin elongated tool that fits into the semi-circular holes along side the AC power cord white wire. Press into the hole gently to release the grip on the wire.

    • The AC power cord wire should release with ease if done properly.

  10. Cut the existing cable tie bundling the other AC power cord, red, orange, gray, and blue wires together.
    • Cut the existing cable tie bundling the other AC power cord, red, orange, gray, and blue wires together.

    • Remove or cut the crimp connector connecting the blue wire and the AC power cord wire.

结论

To reassemble your device, follow these instructions in reverse order.

2等其他人完成本指南。

Chris Hartley

于2012年10月04日注册

364 信誉积分

创作了3篇指南

团队

Cal Poly, Team 24-28, Regan Fall 2012 Cal Poly, Team 24-28, Regan Fall 2012 的会员

CPSU-REGAN-F12S24G28

4 名成员

创作了10篇指南

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 0

总计 393