取消

Disassembling Compaq Mini 110 Fan

撰写者： alea (和另外5个贡献者)

评论： 3
收藏 5
完成 1

Disassembling Compaq Mini 110 Fan

难度

简单

步骤

14

所需时间

1分钟

简介

Abolish the noisy bugger and put in a powerfully quiet cooling device.

工具

购买这些工具

Phillips #0 Screwdriver

US$6.99

购买
Spudger

US$3.99

购买

配件

没有特定配件。

步骤 1 Disassembling Compaq Mini 110 Battery

Find the battery and the battery tabs located on the bottom of the Compaq Mini.

Find the battery and the battery tabs located on the bottom of the Compaq Mini.

Find the battery and the battery tabs located on the bottom of the Compaq Mini.

步骤 2

Push the tabs inward and slide the battery out.

Push the tabs inward and slide the battery out.

Push the tabs inward and slide the battery out.

Push the tabs inward and slide the battery out.

步骤 3 RAM

Find and remove the two screws on the bottom of your Compaq Mini covering the memory compartment.

Note that the screws are attached to the panel.

Find and remove the two screws on the bottom of your Compaq Mini covering the memory compartment.
Note that the screws are attached to the panel.

步骤 4

Push out side tabs.

Push out side tabs.

步骤 5 Keyboard

Remove the rubber pads located on the corners of your Compaq Mini.

There may be junk underneath it. This is residue left from the glue that held on the rubber pad. Just scrape it away to find the screw.

Remove the rubber pads located on the corners of your Compaq Mini.
There may be junk underneath it. This is residue left from the glue that held on the rubber pad. Just scrape it away to find the screw.

步骤 6

Unscrew all the corner screws. There are four total, one under each rubber pad.

Unscrew all the corner screws. There are four total, one under each rubber pad.

Unscrew all the corner screws. There are four total, one under each rubber pad.

步骤 7

Unscrew the screw for the bottom case located in the RAM compartment.

Unscrew the screw for the bottom case located in the RAM compartment.

Unscrew the screw for the bottom case located in the RAM compartment.

步骤 8

Remove the three screws in the silver tabs at the back of the keyboard. The red circles show where they are located at the back of the base under the screen.

Remove the three screws in the silver tabs at the back of the keyboard. The red circles show where they are located at the back of the base under the screen.

Remove the three screws in the silver tabs at the back of the keyboard. The red circles show where they are located at the back of the base under the screen.

步骤 9 Top Cover

Remove the eight screws from the plastic top cover.

Remove the eight screws from the plastic top cover.

步骤 10

Pry up the top plastic cover using a spudger.

Under the screen there are two tabs that need to be pushed in.

Under the screen there are two tabs that need to be pushed in.

Pry up the top plastic cover using a spudger.
Under the screen there are two tabs that need to be pushed in.

步骤 11

Careful lifting up the cover because the track pad is still attached.

Remove the cable by pulling it up.

Careful lifting up the cover because the track pad is still attached.
Remove the cable by pulling it up.

步骤 12 Hard Drive

Remove the three screws.

Remove the three screws.

步骤 13

Pull up on the tab.

Pull up on the tab.

Pull up on the tab.

步骤 14 Fan

Remove the two screws holding the fan in place.

There is still a cable attached to the fan so be sure to pull that out as well.

Remove the two screws holding the fan in place.
There is still a cable attached to the fan so be sure to pull that out as well.

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

作者

与5其他贡献者

alea

于2010年10月06日注册

1,308 信誉积分

创作了14篇指南

+ 10更多徽章

团队

Cal Poly, Team 22-2, Maness Fall 2010 Cal Poly, Team 22-2, Maness Fall 2010 的会员

CPSU-MANESS-F10S22G2

6 名成员

创作了20篇指南

0条评论

添加一条评论

浏览统计数据:

过去的24小时： 0

过去的7天： 3

过去的30天： 6

总计 6,223