简介

A guide on how to remove the Top Cover.

Turn the laptop bottom side up with the rear panel facing forward.
  • Turn the laptop bottom side up with the rear panel facing forward.

添加评论

Remove the two T8 Torx screws that secure the LED cover to the base enclosure.
  • Remove the two T8 Torx screws that secure the LED cover to the base enclosure.

添加评论

Turn the laptop top side up with the front facing forward. Open the screen.
  • Turn the laptop top side up with the front facing forward. Open the screen.

添加评论

Locate the F1 and F2 keys near the top left corner of the keyboard.
  • Locate the F1 and F2 keys near the top left corner of the keyboard.

添加评论

While holding the F1 and F2 keys, insert a spudger between the keys into the notch in the LED cover. Lift up.
  • While holding the F1 and F2 keys, insert a spudger between the keys into the notch in the LED cover. Lift up.

添加评论

Locate the Pause and Scroll keys near the top right corner of the keyboard.
  • Locate the Pause and Scroll keys near the top right corner of the keyboard.

添加评论

While holding the Pause and Scroll keys, insert a spudger between the keys into the notch in the LED cover. Lift up.
  • While holding the Pause and Scroll keys, insert a spudger between the keys into the notch in the LED cover. Lift up.

添加评论

Insert a spudger between the F7 and F8 keys. Lift up to remove the LED cover. Insert a spudger between the F7 and F8 keys. Lift up to remove the LED cover.
  • Insert a spudger between the F7 and F8 keys. Lift up to remove the LED cover.

添加评论

Lift the back edge of the keyboard and pull towards the screen.
  • Lift the back edge of the keyboard and pull towards the screen.

添加评论

Mac RAM 套件
加速你的Mac。充分利用它的内存。
Mac RAM 套件
从Mac中清理出更多内存。
Pull the cable and lift up to release.
  • Pull the cable and lift up to release.

添加评论

Remove the keyboard.
  • Remove the keyboard.

添加评论

Locate the fan near the top left corner. It has three colored wires: yellow, red, and black.
  • Locate the fan near the top left corner. It has three colored wires: yellow, red, and black.

  • Disconnect the cable connecting the fan to the system board.

添加评论

Locate and remove the four screws in the copper plate.
  • Locate and remove the four screws in the copper plate.

添加评论

Remove the heat spreader by pulling the whole assembly up out of the computer.
  • Remove the heat spreader by pulling the whole assembly up out of the computer.

添加评论

Flip the computer bottom side up with the rear facing forward.
  • Flip the computer bottom side up with the rear facing forward.

添加评论

Remove the six screws shown in picture.
  • Remove the six screws shown in picture.

添加评论

Remove battery and then remove screw in  metal support on case edge
  • Remove battery and then remove screw in metal support on case edge

  • Flip the computer top side up with the front facing you.

添加评论

Lift up the palm rest from the front edge and swing it towards the screen.
  • Lift up the palm rest from the front edge and swing it towards the screen.

添加评论

Locate the first connector. Disconnect by firmly pulling up.
  • Locate the first connector. Disconnect by firmly pulling up.

添加评论

Locate the second connector. Remove by firmly pulling up.
  • Locate the second connector. Remove by firmly pulling up.

添加评论

Remove the palm rest.
  • Remove the palm rest.

添加评论

Turn the base bottom side up.
  • Turn the base bottom side up.

添加评论

Remove the two TM 2.5mm x 8.0mm screws that secure the top cover to the base.
  • Remove the two TM 2.5mm x 8.0mm screws that secure the top cover to the base.

添加评论

Turn the base top side up with the front facing forward.
  • Turn the base top side up with the front facing forward.

添加评论

Remove the three TM 2.5 mm x 5.0 mm screws that secure the top cover to the base.
  • Remove the three TM 2.5 mm x 5.0 mm screws that secure the top cover to the base.

添加评论

Lift the top cover straight up about one inch, then slide forward until the microphone cable is exposed.
  • Lift the top cover straight up about one inch, then slide forward until the microphone cable is exposed.

  • Disconnect the microphone cable from the system board.

添加评论

Remove the top cover from the base.
  • Remove the top cover from the base.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

Alex Hernandez

于2010年04月14日注册

28 信誉积分

创作了4篇指南

团队

Cal Poly, Team 29-74, Johann Spring 2010 Cal Poly, Team 29-74, Johann Spring 2010 的会员

CPSU-JOHANN-S10S29G74

3 名成员

创作了7篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 0

总计 2,791