/
我的工作台

快速访问设备的指南、配件和论坛

DE
Deutsch
ES
Español
IT
Italiano
PT
Português
TR
Türkçe
JP
日本語
EN
English
FR
Français
NL
Nederlands
RU
Pусский
ZH
中文
KO
한국어
注册
登录
加入世界上最大的维修社区
Cisco 878 Integrated Services Router StrataFlash Memory module Disassembly

Cisco 878 Integrated Services Router StrataFlash Memory module Disassembly

Jiri Altman

Jiri Altman 和 另一个贡献者

最后更新于 January 19, 2023

30分钟
简单
社区贡献指南

简介

转到步骤 1

This guide helps you to remove the StrataFlash Memory module from Cisco 878 device.

你所需要的

工具

  1. Cisco 878 Integrated Services Router StrataFlash Memory module Disassembly, Remove the two screws on back side: 步骤 1 中的图像 1，3 Cisco 878 Integrated Services Router StrataFlash Memory module Disassembly, Remove the two screws on back side: 步骤 1 中的图像 2，3 Cisco 878 Integrated Services Router StrataFlash Memory module Disassembly, Remove the two screws on back side: 步骤 1 中的图像 3，3

    • Only trained and qualified personnel should be allowed to install, replace, or service this equipment!

    • During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself!

    • Make sure that the power switch is turned to standby and that the power supply cable is disconnected. Disconnect all cables from the router back panel.

    • Use the Phillips #1 Screwdriver to remove the two screws on back side of the device.

    编辑

  2. Cisco 878 Integrated Services Router StrataFlash Memory module Disassembly, Remove top cover: 步骤 2 中的图像 1，3 Cisco 878 Integrated Services Router StrataFlash Memory module Disassembly, Remove top cover: 步骤 2 中的图像 2，3 Cisco 878 Integrated Services Router StrataFlash Memory module Disassembly, Remove top cover: 步骤 2 中的图像 3，3

    • 1. Gently push the top cover of the router away from you.

    • 2. Lift it up top cover from the bottom of the router.

    • 3. Remove top cover from the device.

    • Place the router bottom on an antistatic mat.

    编辑

  4. Cisco 878 Integrated Services Router StrataFlash Memory module Disassembly, Remove the three screws on front side: 步骤 3 中的图像 1，2 Cisco 878 Integrated Services Router StrataFlash Memory module Disassembly, Remove the three screws on front side: 步骤 3 中的图像 2，2

    • Use the Phillips #1 Screwdriver to remove the three screws on front side of the device.

    编辑

  5. Cisco 878 Integrated Services Router StrataFlash Memory module Disassembly, Remove the inner metal shield: 步骤 4 中的图像 1，3 Cisco 878 Integrated Services Router StrataFlash Memory module Disassembly, Remove the inner metal shield: 步骤 4 中的图像 2，3 Cisco 878 Integrated Services Router StrataFlash Memory module Disassembly, Remove the inner metal shield: 步骤 4 中的图像 3，3

    • 1. Gently lift up inner metal shield from the bottom of the router.

    • 2. Remove inner metal shield from the device (see the anchors on the picture).

    • Be careful and do not distort the plates!

    编辑

  6. Cisco 878 Integrated Services Router StrataFlash Memory module Disassembly, Remove StrataFlash Memory module: 步骤 5 中的图像 1，3 Cisco 878 Integrated Services Router StrataFlash Memory module Disassembly, Remove StrataFlash Memory module: 步骤 5 中的图像 2，3 Cisco 878 Integrated Services Router StrataFlash Memory module Disassembly, Remove StrataFlash Memory module: 步骤 5 中的图像 3，3

    • 1. Place your fingers on the levers at the two sides of the slot, and push open.

    • 2. Firmly pull the release lever away from the module until the module pops up.

    • 3. You can then remove the module from the module slot.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

作者

与1其他贡献者

Jiri Altman

于05/03/16注册

1,539 声望

创作了9篇指南

徽章: 23

+ 20更多徽章

团队

4k20 Repair Team 4k20 Repair Team 的会员

Community

2 名成员

创作了17篇指南

0指南评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 2

过去 30 天： 14

总计 357