配件

无需配件。

  1. Remove the four screws on the side of the speaker.
    • Remove the four screws on the side of the speaker.

  2. Remove the two back screws on the bottom of the camera.
    • Remove the two back screws on the bottom of the camera.

    • Note: Bottom screws are longer than the top ones, so label accordingly for easy reassembly.

  3. Remove the four screws on the side opposite of the speaker.
    • Remove the four screws on the side opposite of the speaker.

  4. Once all screws have been removed, gently pry open bottom casing. With tweezers, carefully remove ribbon from LCD screen.
    • Once all screws have been removed, gently pry open bottom casing.

    • With tweezers, carefully remove ribbon from LCD screen.

    • Set bottom casing aside.

  5. Gently pry apart the top casing using tweezers. Set the top casing aside. Set the top casing aside.
    • Gently pry apart the top casing using tweezers.

    • Set the top casing aside.

  6. 所有超过US$100.00或包含 Pro Tech工具包的订单免费送货!

    浏览我们的商店

    善于维修,即天赋异禀。

    与 #ImAGenius 分享您的维修故事

    我们都是天才

    与 #ImAGenius 分享您的维修故事

  7. Use tweezers or prongs to pry the LCD screen off from the opening. Note: The bottom of the LCD screen is attached to the frame by a few pieces of black tape.
    • Use tweezers or prongs to pry the LCD screen off from the opening.

    • Note: The bottom of the LCD screen is attached to the frame by a few pieces of black tape.

  8. Lift up the LCD screen, slowly move it to the other side. Lift up the LCD screen, slowly move it to the other side.
    • Lift up the LCD screen, slowly move it to the other side.

  9. Pry off the LCD casing. Pry off the LCD casing.
    • Pry off the LCD casing.

  10. Flip open the connector holding the ribbon. Pull out the LCD screen with the ribbon from the camera. Pull out the LCD screen with the ribbon from the camera.
    • Flip open the connector holding the ribbon.

    • Pull out the LCD screen with the ribbon from the camera.

  11. Remove two screws on the side where the battery is located. Remove the lanyard loop after the screws come off.
    • Remove two screws on the side where the battery is located.

    • Remove the lanyard loop after the screws come off.

    • Slowly pull the side casing so it becomes dislocated from the top of the camera frame.

  12. On the front of the camera near the flash flip the connector holding the ribbon. Remove the ribbon from the connector.
    • On the front of the camera near the flash flip the connector holding the ribbon.

    • Remove the ribbon from the connector.

  13. Carefully remove the L shaped frame from the camera. At the bottom of the camera the L shaped frame is being held in by two plastic bumps and a metal tab. Pop the frame off the bumps and tabs.
    • Carefully remove the L shaped frame from the camera.

    • At the bottom of the camera the L shaped frame is being held in by two plastic bumps and a metal tab.

    • Pop the frame off the bumps and tabs.

    • Note: There is a yellow and orange wire soldered onto the camera. Be careful not to pull them off.

  14. This is the flash assembly. It needs to be removed with soldering points circled.
    • This is the flash assembly.

    • It needs to be removed with soldering points circled.

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

Christian

于2011年01月28日注册

320 信誉积分

创作了3篇指南

团队

Cal Poly, Team 4-38, Regan Winter 2011 Cal Poly, Team 4-38, Regan Winter 2011 的会员

CPSU-REGAN-W11S4G38

4 名成员

创作了7篇指南

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 0

总计 2,455