Locate 12 screws. Four on the left, four on the right, and four on the bottom. Locate 12 screws. Four on the left, four on the right, and four on the bottom. Locate 12 screws. Four on the left, four on the right, and four on the bottom.
  • Locate 12 screws. Four on the left, four on the right, and four on the bottom.

添加评论

Using the #00 Phillips screwdriver, remove the four 3.66mm screws from the bottom outer case, and the eight 1.75mm screw from the sides of the case.
  • Using the #00 Phillips screwdriver, remove the four 3.66mm screws from the bottom outer case, and the eight 1.75mm screw from the sides of the case.

添加评论

Separate the front case from the body of the camera.
  • Separate the front case from the body of the camera.

添加评论

Separate the back case from the body of the camera.
  • Separate the back case from the body of the camera.

添加评论

Remove the metal grating located to the right of the LCD screen by inserting the plastic opening tool under the grating and pulling up. Remove the metal grating located to the right of the LCD screen by inserting the plastic opening tool under the grating and pulling up. Remove the metal grating located to the right of the LCD screen by inserting the plastic opening tool under the grating and pulling up.
  • Remove the metal grating located to the right of the LCD screen by inserting the plastic opening tool under the grating and pulling up.

添加评论

Mac RAM 套件
加速你的Mac。充分利用它的内存。
Mac RAM 套件
从Mac中清理出更多内存。
Before removing the side metal bracket, first remove the attached strap knob by twisting it off.
  • Before removing the side metal bracket, first remove the attached strap knob by twisting it off.

  • Then, remove the side metal bracket by inserting the plastic opening tool under the bracket and pulling up.

添加评论

Using the plastic opening tool, pry up the LCD screen starting at one of the corners. Insert the tool under one of the corners and lift up.
  • Using the plastic opening tool, pry up the LCD screen starting at one of the corners. Insert the tool under one of the corners and lift up.

添加评论

Continue to lift the LCD screen all the way up. Be careful not to rip any wires connecting the LCD screen to the top of the camera.
  • Continue to lift the LCD screen all the way up.

  • Be careful not to rip any wires connecting the LCD screen to the top of the camera.

添加评论

Remove the orange strip by grabbing the white tab and pulling. Remove the orange strip by grabbing the white tab and pulling.
  • Remove the orange strip by grabbing the white tab and pulling.

添加评论

Remove the two 1.68mm screws located on the motherboard, using a #00 Phillips screwdriver.
  • Remove the two 1.68mm screws located on the motherboard, using a #00 Phillips screwdriver.

添加评论

Using the plastic opening tool, pry the battery case clamps (located on front of the camera) so that the bottom will come loose.
  • Using the plastic opening tool, pry the battery case clamps (located on front of the camera) so that the bottom will come loose.

添加评论

Detach the inner orange strip from the motherboard to the lens by inserting the plastic opening tool under the tab and llifting up.
  • Detach the inner orange strip from the motherboard to the lens by inserting the plastic opening tool under the tab and llifting up.

添加评论

Fully remove the motherboard from the lens.
  • Fully remove the motherboard from the lens.

  • It will be still be attached by wires and a different orange strip.

there is no cautionary notes about being extra careful to not touch certain parts...?

cagineer - 回复

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

Taylor

于2012年04月18日注册

31 信誉积分

撰写一个指南

团队

Cal Poly, Team 9-45, Regan Spring 2012 Cal Poly, Team 9-45, Regan Spring 2012 的会员

CPSU-REGAN-S12S9G45

7 名成员

创作了6篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 3

总计 571