简介

The screen is a crucial part of the camera: it displays images for consumers to view their pictures instantly. Damage to the screen may require replacement.

Slide grey latch to open the battery compartment. Slide grey latch to open the battery compartment.
  • Slide grey latch to open the battery compartment.

添加评论

Push orange retaining clip to the right to free battery. Push orange retaining clip to the right to free battery.
  • Push orange retaining clip to the right to free battery.

添加评论

Remove battery from the camera.
  • Remove battery from the camera.

添加评论

Remove the lanyard.
  • Remove the lanyard.

添加评论

Remove the two 2.3mm screws (underneath the name plate) and two 2.8mm screws (next to the threaded tripod mount) from the bottom face of the camera.
  • Remove the two 2.3mm screws (underneath the name plate) and two 2.8mm screws (next to the threaded tripod mount) from the bottom face of the camera.

  • Be careful to keep track of the different screw sizes as you proceed with this guide.

添加评论

Remove the single 3.8mm screw from the back face of the camera.
  • Remove the single 3.8mm screw from the back face of the camera.

添加评论

Remove the two 2.3mm screws from the right face of the camera.
  • Remove the two 2.3mm screws from the right face of the camera.

添加评论

Remove the two 3.2mm screws (outside edge) and two 3.7mm screws (towards middle) from the left side of the camera body.
  • Remove the two 3.2mm screws (outside edge) and two 3.7mm screws (towards middle) from the left side of the camera body.

添加评论

Mac RAM 套件
加速你的Mac。充分利用它的内存。
Mac RAM 套件
从Mac中清理出更多内存。
Pull the back face panel away from the front end of the body. This may take some wiggling and force.
  • Pull the back face panel away from the front end of the body. This may take some wiggling and force.

添加评论

Remove the CF card door from the left side of the camera body. Remove the CF card door from the left side of the camera body.
  • Remove the CF card door from the left side of the camera body.

添加评论

Remove the rubber digital a/v out cap by sliding it out of the groove on the front plate. Remove the rubber digital a/v out cap by sliding it out of the groove on the front plate.
  • Remove the rubber digital a/v out cap by sliding it out of the groove on the front plate.

添加评论

Remove the front face by sliding it off.
  • Remove the front face by sliding it off.

添加评论

Remove the rubber seal that goes over the right side of the viewfinder.
  • Remove the rubber seal that goes over the right side of the viewfinder.

添加评论

Remove the two 3.9mm screws that retain the laminated cooper sheet.
  • Remove the two 3.9mm screws that retain the laminated cooper sheet.

添加评论

Remove the seven wire connections that connect to the motherboard. Remove the seven wire connections that connect to the motherboard.
  • Remove the seven wire connections that connect to the motherboard.

添加评论

Remove the single 3.8mm screw that is on the motherboard.
  • Remove the single 3.8mm screw that is on the motherboard.

添加评论

Carefully remove the motherboard from the main frame of the camera body.
  • Carefully remove the motherboard from the main frame of the camera body.

添加评论

After completing the removal of the motherboard, remove the tripod mounting screws (3.4mm) on the left side
  • After completing the removal of the motherboard, remove the tripod mounting screws (3.4mm) on the left side

添加评论

Carefully pry the left side of the housing plate from the bottom of the tripod mounting plate, releasing it from the two alignment pegs next to the screws
  • Carefully pry the left side of the housing plate from the bottom of the tripod mounting plate, releasing it from the two alignment pegs next to the screws

添加评论

Lift the left side of the tripod mounting plate towards you, lift free the mounting plate from the rest of the assembly
  • Lift the left side of the tripod mounting plate towards you, lift free the mounting plate from the rest of the assembly

  • Be careful because there are still wire connections attached to the mounting plate which you don't want to remove

添加评论

Remove the 2.1mm screws from the bottom and top of the screen connecting it to the housing plate
  • Remove the 2.1mm screws from the bottom and top of the screen connecting it to the housing plate

添加评论

Unsolder the four points at the top of the screen with a soldering iron
  • Unsolder the four points at the top of the screen with a soldering iron

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

Anh

于2011年04月13日注册

121 信誉积分

撰写一个指南

团队

Cal Poly, Team 20-70, Walters Spring 2011 Cal Poly, Team 20-70, Walters Spring 2011 的会员

CPSU-WALTERS-S11S20G70

5 名成员

创作了4篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 1

过去的30天: 1

总计 1,367