简介

The lens is used for capturing specific scenes and to feed these scenes into the camera.

配件

无需配件。

  1. Slide grey latch to open the battery compartment.
    • Slide grey latch to open the battery compartment.

    添加评论

  2. Push orange retaining clip to the right to free battery.
    • Push orange retaining clip to the right to free battery.

    添加评论

    • Remove battery from the camera.

    添加评论

    • Remove the lanyard.

    添加评论

    • Remove the two 2.3mm screws (underneath the name plate) and two 2.8mm screws (next to the threaded tripod mount) from the bottom face of the camera.

    • Be careful to keep track of the different screw sizes as you proceed with this guide.

    添加评论

    • Remove the single 3.8mm screw from the back face of the camera.

    添加评论

    • Remove the two 2.3mm screws from the right face of the camera.

    添加评论

    • Remove the two 3.2mm screws (outside edge) and two 3.7mm screws (towards middle) from the left side of the camera body.

    添加评论

    • Pull the back face panel away from the front end of the body. This may take some wiggling and force.

    添加评论

  3. 订单满 $20 免运费
    结账时使用优惠码 BLUEANDBLACK
    订单满 $20 免运费
    使用优惠码 BLUEANDBLACK
    • Remove the CF card door from the left side of the camera body.

    添加评论

    • Remove the rubber digital a/v out cap by sliding it out of the groove on the front plate.

    添加评论

    • Remove the front face by sliding it off.

    添加评论

    • Remove the rubber seal that goes over the right side of the viewfinder.

    添加评论

    • Remove the two 3.9mm screws that retain the laminated cooper sheet.

    添加评论

    • Remove the seven wire connections that connect to the motherboard.

    添加评论

    • Remove the single 3.8mm screw that is on the motherboard.

    添加评论

    • Carefully remove the motherboard from the main frame of the camera body.

    添加评论

    • After completing the removal of the motherboard, remove the tripod mounting screws (3.4mm) on the left side

    添加评论

    • Carefully pry the left side of the housing plate from the bottom of the tripod mounting plate, releasing it from the two alignment pegs next to the screws

    添加评论

    • Lift the left side of the tripod mounting plate towards you, lift free the mounting plate from the rest of the assembly

    • Be careful because there are still wire connections attached to the mounting plate which you don't want to remove

    添加评论

    • Remove the 2.1mm screws from the bottom and top of the screen connecting it to the housing plate

    添加评论

    • Unsolder the four points at the top of the screen with a soldering iron

    添加评论

    • You do not need to unsolder the screen to get to the lens, but follow the rest of the steps to free the screen from the housing plate.

    添加评论

    • Remove the card-reader shield by removing the screw at the top of the shield.

    添加评论

    • Remove the 2 black screws that attach the battery box to the housing plate.

    • The second picture shows the battery box detached from the housing plate.

    添加评论

    • Remove the three (3.1mm) black screws that were behind the screen and battery box.

    添加评论

    • Carefully remove the lens.

    • Remove the bottom side of the lens first before the viewfinder side.

    • Be careful of wires and delicate parts.

    添加评论

结论

To reassemble your device, follow these instructions in reverse order.

Joseph Melo

于2011年04月07日注册

111 信誉积分

撰写一个指南

团队

Cal Poly, Team 20-70, Walters Spring 2011 Cal Poly, Team 20-70, Walters Spring 2011 的会员

CPSU-WALTERS-S11S20G70

5 名成员

创作了4篇指南

Camera in the pictures is not Canon Powershot S200

jkovalai - 回复

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 3

总计 1,437