修复你的物品 社区 商店

Canon PowerShot SX50 HS Rear Case Replacement

简介

Remove the back encasement of the Canon PowerShot SX50 HS.

你所需要的

  1. Canon PowerShot SX50 HS Rear Case Replacement, Battery: 步骤 1 中的图像 1，1

    • Locate the battery compartment on the bottom of the camera.

    • Push the latch on the outside of the battery door to the right to get to the battery pack inside.

    翻译

  2. Canon PowerShot SX50 HS Rear Case Replacement: 步骤 2 中的图像 1，1

    • Pull the brown latch on the inside of the battery door towards your palm (to the left). The battery pack should pop out (battery not pictured).

    • Now remove the battery pack from the camera with your fingers.

    翻译

  3. Canon PowerShot SX50 HS Rear Case Replacement, Rear Case: 步骤 3 中的图像 1，2 Canon PowerShot SX50 HS Rear Case Replacement, Rear Case: 步骤 3 中的图像 2，2

    • Remove the two Phillips #000 screws, length 5 mm, on either side of the viewfinder.

    • Remove the one Phillips #000 screw, length 4 mm, on the bottom, closer to the back side of the camera.

    翻译

  5. Canon PowerShot SX50 HS Rear Case Replacement: 步骤 4 中的图像 1，2 Canon PowerShot SX50 HS Rear Case Replacement: 步骤 4 中的图像 2，2

    • Remove the two Phillips #000 screws, length 3 mm, on the left side of camera.

    • Remove the Phillips #000 screw, length 4 mm, located between the two 3 mm screws.

    • Remove the two Phillips #000 screws, length 4 mm, on the bottom left corner of the camera.

    翻译

  6. Canon PowerShot SX50 HS Rear Case Replacement: 步骤 5 中的图像 1，1

    • Find the "A/V Out Digital" charging station and lift up the flap.

    • Remove the two Phillips #000 screws, length 5 mm, that are under the "A/V Out Digital" flap.

    • Remove the one Phillips #000 screw, length 5 mm, that is outside the "A/V Out Digital" flap.

    翻译

  7. Canon PowerShot SX50 HS Rear Case Replacement: 步骤 6 中的图像 1，2 Canon PowerShot SX50 HS Rear Case Replacement: 步骤 6 中的图像 2，2

    • Use the plastic opening tool to carefully start lifting up the camera's left-side panel. Then use your fingers to pry off the rest.

    翻译

  8. Canon PowerShot SX50 HS Rear Case Replacement: 步骤 7 中的图像 1，3 Canon PowerShot SX50 HS Rear Case Replacement: 步骤 7 中的图像 2，3 Canon PowerShot SX50 HS Rear Case Replacement: 步骤 7 中的图像 3，3

    • Make sure the LCD screen panel, the battery compartment door, and the 'A/V Out Digital" flap are all open.

    • Using your fingers, carefully pry off the back encasement (you may need to use a plastic opening tool to help you).

    • Do not remove the back casing too far or too quickly. There is a wire ribbon attaching the back encasement to the motherboard that is very delicate.

    翻译

  9. Canon PowerShot SX50 HS Rear Case Replacement: 步骤 8 中的图像 1，3 Canon PowerShot SX50 HS Rear Case Replacement: 步骤 8 中的图像 2，3 Canon PowerShot SX50 HS Rear Case Replacement: 步骤 8 中的图像 3，3

    • Find the orange wire ribbon attaching the back encasement to the I/O board in the lower right-hand corner of the camera (lens facing away).

    • Carefully lift up the brown clip holding the wire ribbon in place and pull the ribbon out of the clasp with your fingers or tweezers.

    • Be cautious when the removing the wire ribbon; it is very delicate.

    翻译

  10. Canon PowerShot SX50 HS Rear Case Replacement: 步骤 9 中的图像 1，1

    • Now you can completely separate the back encasement from the rest of the camera.

    翻译
结论

To reassemble your device, follow these instructions in reverse order.

3等其他人完成本指南。

作者

与5其他贡献者

Daniel Gurrola

于04/01/15注册

267 声望

创作了2篇指南

徽章: 10

+ 7更多徽章

团队

Cal Poly, Team 12-7, Lancaster Spring 2015 Cal Poly, Team 12-7, Lancaster Spring 2015 的会员

CPSU-LANCASTER-S15S12G7

5 名成员

创作了7篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 1

过去 7 天： 1

过去 30 天： 4

总计 1,071