修复你的物品 社区 商店

Canon PowerShot S500 Logic Board Replacement

简介

This is a guide to removing the camera's logic board.

你所需要的

  1. Canon PowerShot S500 Logic Board Replacement, Front and Rear Casing : 步骤 1 中的图像 1，2 Canon PowerShot S500 Logic Board Replacement, Front and Rear Casing : 步骤 1 中的图像 2，2

    • Unscrew five Phillips screws using a #0 Phillips screwdriver.

    • One screw is on upper right corner of the back panel.

    • The other four screws are on the bottom of the camera.

    编辑

  2. Canon PowerShot S500 Logic Board Replacement: 步骤 2 中的图像 1，1

    • Open the memory card cover by moving the slide switch toward the top end of of the camera.

    • Remove the memory card from the slot.

    编辑

  3. Canon PowerShot S500 Logic Board Replacement: 步骤 3 中的图像 1，1

    • Remove the rear cover from the rest of the camera.

    • This may require gentle rocking of the case to free it.

    编辑

  4. Canon PowerShot S500 Logic Board Replacement: 步骤 4 中的图像 1，2 Canon PowerShot S500 Logic Board Replacement: 步骤 4 中的图像 2，2

    • Unscrew the four Phillips screws from the side of the casing and one screw from the bottom using a #0 Phillips screwdriver.

    编辑

  5. Canon PowerShot S500 Logic Board Replacement: 步骤 5 中的图像 1，1

    • Free the front cover from the rest of the camera.

    • The cover may require gentle rocking to remove.

    编辑

  6. Canon PowerShot S500 Logic Board Replacement, LCD: 步骤 6 中的图像 1，1

    • Unscrew two Phillips screws above the LCD using a #0 Phillips screwdriver.

    编辑

  7. Canon PowerShot S500 Logic Board Replacement: 步骤 7 中的图像 1，1

    • Gently separate the top of LCD from the rest of the camera using your thumb.

    • Be careful not pull the LCD too far because of the ribbon cable connection.

    • Place the Spudger in the hole of the electrical ribbon.

    • Gently pull the ribbon down using the Spudger until it is free from the camera but still connected to the LCD.

    • The LCD will still be connected to the rest of the camera

    编辑

  8. Canon PowerShot S500 Logic Board Replacement: 步骤 8 中的图像 1，2 Canon PowerShot S500 Logic Board Replacement: 步骤 8 中的图像 2，2

    • Unscrew single Phillips screw with a #0 Phillips screwdriver.

    • Free the bottom panel and attached ribbon from the rest of the camera.

    • Be careful not to damage the ribbon.

    编辑

  10. Canon PowerShot S500 Logic Board Replacement: 步骤 9 中的图像 1，1

    • Turn over the camera.

    • Lift the clear plastic from the face of the camera, peeling the adhesive just below the zoom lens.

    • The plastic will still be connected on the left side.

    编辑

  11. Canon PowerShot S500 Logic Board Replacement: 步骤 10 中的图像 1，1

    • Place the Spudger between the orange ribbon and the black ribbon gate.

    • Lift the ribbon gate using the Spudger.

    编辑

  12. Canon PowerShot S500 Logic Board Replacement: 步骤 11 中的图像 1，1

    • Place the Spudger in the corner of the ribbon above the hole.

    • Remove the ribbon from the ribbon gate by pulling the Spudger away from the gate.

    编辑

  13. Canon PowerShot S500 Logic Board Replacement: 步骤 12 中的图像 1，1

    • Free this ribbon and the bottom panel from the rest of the camera.

    • Be careful not to damage the ribbon.

    编辑

  14. Canon PowerShot S500 Logic Board Replacement: 步骤 13 中的图像 1，1

    • Turn the camera over so you can see the LCD.

    • Remove single Phillips screw below the LCD using a #0 Phillips screwdriver.

    编辑

  15. Canon PowerShot S500 Logic Board Replacement: 步骤 14 中的图像 1，1

    • Lift the blue ribbon gate using the Spudger.

    编辑

  16. Canon PowerShot S500 Logic Board Replacement: 步骤 15 中的图像 1，1

    • Insert the Spudger into the hole of the ribbon.

    • Move the Spudger away from the gate to fully remove ribbon.

    • Be careful not to damage the ribbon.

    编辑

  17. Canon PowerShot S500 Logic Board Replacement: 步骤 16 中的图像 1，1

    • Lift the LCD away from the rest of the camera.

    编辑

  18. Canon PowerShot S500 Logic Board Replacement, Logic Board: 步骤 17 中的图像 1，2 Canon PowerShot S500 Logic Board Replacement, Logic Board: 步骤 17 中的图像 2，2

    • Lift off the capture button by wiggling it back and forth while pulling upward.

    • Be careful not to damage the two clips.

    编辑

  19. Canon PowerShot S500 Logic Board Replacement: 步骤 18 中的图像 1，2 Canon PowerShot S500 Logic Board Replacement: 步骤 18 中的图像 2，2

    • Flip open the four ribbon gates using the Spudger.

    • Gently pull out the ribbon cables from the gates using the Spudger.

    编辑

  20. Canon PowerShot S500 Logic Board Replacement: 步骤 19 中的图像 1，1

    • Unscrew the four Phillips screws using a #0 Phillips screwdriver.

    编辑

  21. Canon PowerShot S500 Logic Board Replacement: 步骤 20 中的图像 1，2 Canon PowerShot S500 Logic Board Replacement: 步骤 20 中的图像 2，2

    • Gently lift the logic board.

    • Be careful not to pull too hard and damage the white ribbon cable.

    • Place the Spudger so that it is between the logic board, the white ribbon cable, and the rest of the camera.

    • Remove the white ribbon cable by pulling the Spudger away from the camera, keeping it parallel to the logic board.

    编辑

  22. Canon PowerShot S500 Logic Board Replacement: 步骤 21 中的图像 1，1

    • Lay the logic board back down so that it is resting on the body of the camera.

    • Pull the two plugs (white and green) out to the right from the logic board using the tweezers.

    编辑

  23. Canon PowerShot S500 Logic Board Replacement: 步骤 22 中的图像 1，2 Canon PowerShot S500 Logic Board Replacement: 步骤 22 中的图像 2，2

    • We're now ready to begin the desoldering process. You'll need a soldering iron, solder, and desoldering wick. You should be able to find these items at a Radio Shack if you don't already have them.

    • Please do not perform this step if you are not comfortable or have previous experience with soldering. Doing so, could cause severe damage to your camera.

    • Desolder the two soldered ribbon cables attached to the logic board.

    编辑

  24. Canon PowerShot S500 Logic Board Replacement: 步骤 23 中的图像 1，1

    • Free the logic board from the rest of the camera.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

作者

与6其他贡献者

Nathan Balcom

于01/21/10注册

81 声望

创作了8篇指南

徽章: 9

+ 6更多徽章

团队

Cal Poly, Team 16-28, Maness Winter 2010 Cal Poly, Team 16-28, Maness Winter 2010 的会员

CPSU-MANESS-W10S16G28

4 名成员

创作了8篇指南

一条评论

How brilliant! Great pictures! But where did you buy the new logic board?

Rosario - 回复

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 0

过去 30 天： 2

总计 2,786