修复你的物品

维修的权力

配件 & 工具

Canon PowerShot S500 LCD Replacement

撰写者： Nathan Balcom (和另外6个贡献者)
  • 评论： 0
  • 收藏 1

难度

中等

步骤

16

所需时间

30分钟

节

2

标志

0

简介

This shows how to replace the LCD.

工具

购买这些工具

配件

没有特定配件。

  1. Unscrew five Phillips screws using a #0 Phillips screwdriver. One screw is on upper right corner of the back panel.

    • Unscrew five Phillips screws using a #0 Phillips screwdriver.

    • One screw is on upper right corner of the back panel.

    • The other four screws are on the bottom of the camera.

    编辑

  2. Open the memory card cover by moving the slide switch toward the top end of of the camera.

    • Open the memory card cover by moving the slide switch toward the top end of of the camera.

    • Remove the memory card from the slot.

    编辑

  3. Remove the rear cover from the rest of the camera.

    • Remove the rear cover from the rest of the camera.

    • This may require gentle rocking of the case to free it.

    编辑

  4. Unscrew the four Phillips screws from the side of the casing and one screw from the bottom using a #0 Phillips screwdriver. Unscrew the four Phillips screws from the side of the casing and one screw from the bottom using a #0 Phillips screwdriver.

    • Unscrew the four Phillips screws from the side of the casing and one screw from the bottom using a #0 Phillips screwdriver.

    编辑

  5. Free the front cover from the rest of the camera.

    • Free the front cover from the rest of the camera.

    • The cover may require gentle rocking to remove.

    编辑

  6. Unscrew two Phillips screws above the LCD using a #0 Phillips screwdriver.

    • Unscrew two Phillips screws above the LCD using a #0 Phillips screwdriver.

    编辑

  7. LCD iPhone 屏幕维修套装

    预算选项，涵盖在我们的终身保修中。

    购买套装

    LCD iPhone 屏幕维修套装

    削减维修成本，而不是质量。

    购买套装

  8. Gently separate the top of LCD from the rest of the camera using your thumb.

    • Gently separate the top of LCD from the rest of the camera using your thumb.

    • Be careful not pull the LCD too far because of the ribbon cable connection.

    • Place the Spudger in the hole of the electrical ribbon.

    • Gently pull the ribbon down using the Spudger until it is free from the camera but still connected to the LCD.

    • The LCD will still be connected to the rest of the camera

    编辑

  9. Unscrew single Phillips screw with a #0 Phillips screwdriver. Free the bottom panel and attached ribbon from the rest of the camera.

    • Unscrew single Phillips screw with a #0 Phillips screwdriver.

    • Free the bottom panel and attached ribbon from the rest of the camera.

    • Be careful not to damage the ribbon.

    编辑

  10. Turn over the camera.

    • Turn over the camera.

    • Lift the clear plastic from the face of the camera, peeling the adhesive just below the zoom lens.

    • The plastic will still be connected on the left side.

    编辑

  11. Place the Spudger between the orange ribbon and the black ribbon gate.

    • Place the Spudger between the orange ribbon and the black ribbon gate.

    • Lift the ribbon gate using the Spudger.

    编辑

  12. Place the Spudger in the corner of the ribbon above the hole.

    • Place the Spudger in the corner of the ribbon above the hole.

    • Remove the ribbon from the ribbon gate by pulling the Spudger away from the gate.

    编辑

  13. Free this ribbon and the bottom panel from the rest of the camera.

    • Free this ribbon and the bottom panel from the rest of the camera.

    • Be careful not to damage the ribbon.

    编辑

  14. Turn the camera over so you can see the LCD.

    • Turn the camera over so you can see the LCD.

    • Remove single Phillips screw below the LCD using a #0 Phillips screwdriver.

    编辑

  15. Lift the blue ribbon gate using the Spudger.

    • Lift the blue ribbon gate using the Spudger.

    编辑

  16. Insert the Spudger into the hole of the ribbon.

    • Insert the Spudger into the hole of the ribbon.

    • Move the Spudger away from the gate to fully remove ribbon.

    • Be careful not to damage the ribbon.

    编辑

  17. Lift the LCD away from the rest of the camera.

    • Lift the LCD away from the rest of the camera.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

作者

与6其他贡献者

Nathan Balcom

于2010年01月21日注册

81 信誉积分

创作了8篇指南

徽章: 9

+ 6更多徽章

团队

Cal Poly, Team 16-28, Maness Winter 2010 Cal Poly, Team 16-28, Maness Winter 2010 的会员

CPSU-MANESS-W10S16G28

4 名成员

创作了8篇指南

0条评论

添加一条评论

添加评论

浏览统计数据:

过去的24小时： 0

过去的7天： 0

过去的30天： 0

总计 2,904