简介

Use this guide to remove and/or replace the motherboard on the left side of the camera.

  1. Place camera LCD side up and press up on the battery door. Let it swing open until you can see the battery inside.
    • Place camera LCD side up and press up on the battery door.

    • Let it swing open until you can see the battery inside.

  2. Press down on the orange plastic.
    • Press down on the orange plastic.

    • This will gently eject the battery from its compartment.

  3. Holding the edges, slide out the battery. Holding the edges, slide out the battery.
    • Holding the edges, slide out the battery.

  4. Look at the camera from the side with the lanyard and 4 screws.
    • Look at the camera from the side with the lanyard and 4 screws.

      • Remove the two 3.4 mm screws on the metallic colored part.

  5. Remove the 3mm screw on the top left.
    • Remove the 3mm screw on the top left.

      • NOTE: When reassembling, it is helpful to put the top screw back in before placing the front cover back on the camera.

    • Now remove the 5.3mm screw on the bottom.

  6. Place the camera LCD side down.
    • Place the camera LCD side down.

    • Remove the two 5.3mm screws by the battery door.

  7. 所有超过US$100.00或包含 Pro Tech工具包的订单免费送货!

    浏览我们的商店

    善于维修,即天赋异禀。

    与 #ImAGenius 分享您的维修故事

    我们都是天才

    与 #ImAGenius 分享您的维修故事

  8. Remove the four 3.4mm screws on the bottom of the camera around the tripod mount.
    • Remove the four 3.4mm screws on the bottom of the camera around the tripod mount.

      • Make sure to keep these screws separate from the previous 5.3 mm screws.

  9. Stand the camera back up.
    • Stand the camera back up.

    • Remove the two 3.6mm screws on the side with the A/V Out port.

  10. Lift open the rubber flap covering the A/V Out port.
    • Lift open the rubber flap covering the A/V Out port.

      • Remove the 3.4mm screw in the center.

      • During reassembly, put the A/V out rubber door on before replacing the front panel of the camera

  11. Use a spudger and gently open up the front panel of the camera.
    • Use a spudger and gently open up the front panel of the camera.

      • A thin plastic ribbon will stay connected by a brown piece to front panel of the camera.

  12. There will be a brown plastic piece keeping the thin plastic ribbon in place.
    • There will be a brown plastic piece keeping the thin plastic ribbon in place.

    • Use the spudger to pull out the brown plastic piece attached to the orange plastic.

  13. Use a pair of tweezers and remove the metal piece inside the camera.
    • Use a pair of tweezers and remove the metal piece inside the camera.

  14. Remove the battery door
    • Remove the battery door

      • NOTE: Putting this back on requires aligning the spring on the back of the door with the hole on the camera

  15. Disconnect the black and red cable on the left side of the lens.
    • Disconnect the black and red cable on the left side of the lens.

  16. Disconnect the two orange ribbons on the front of the mother board.
    • Disconnect the two orange ribbons on the front of the mother board.

  17. Pull off the orange ribbon on the upper left of the motherboard.
    • Pull off the orange ribbon on the upper left of the motherboard.

      • This will become available only after removing the ribbon on top.

    • Remove the other two orange ribbons on the middle of the left motherboard.

  18. Remove the 3.3mm screw halfway up the left side of the motherboard just to the left of the lens.
    • Remove the 3.3mm screw halfway up the left side of the motherboard just to the left of the lens.

    • Go under the piece of plastic and remove the 2.6mm screw.

  19. Unplug the top part of the left motherboard. Gently lift the left motherboard up to remove
    • Unplug the top part of the left motherboard.

      • Gently lift the left motherboard up to remove

结论

To reassemble your device, follow these instructions in reverse order.

Jacob

于2012年03月29日注册

13 信誉积分

创作了3篇指南

团队

Cal Poly, Team 7-34, Maness Spring 2012 Cal Poly, Team 7-34, Maness Spring 2012 的会员

CPSU-MANESS-S12S7G34

5 名成员

创作了6篇指南

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 5

总计 829