跳转到主内容

简介

This guide will show you how to remove the front and back casing of the camera.

配件

没有特定配件。

  1. On the bottom of the camera, use your thumb to press the rubber battery cover towards the side of the camera with the strap base. The cover will shift to extend beyond the rest of the camera.
    • On the bottom of the camera, use your thumb to press the rubber battery cover towards the side of the camera with the strap base. The cover will shift to extend beyond the rest of the camera.

  2. Hold the end of the battery cover that extends beyond the camera and lift it up.
    • Hold the end of the battery cover that extends beyond the camera and lift it up.

  3. Pull back on the orange tab to release the battery.
    • Pull back on the orange tab to release the battery.

  4. Pull the battery out.
    • Pull the battery out.

  5. Locate the sliding button labeled "CF open" on the back of the camera. Press and slide down the button labeled "CF open". The memory card cover will pop open. Press and slide down the button labeled "CF open". The memory card cover will pop open.
    • Locate the sliding button labeled "CF open" on the back of the camera.

    • Press and slide down the button labeled "CF open". The memory card cover will pop open.

  6. Push down on the black square button next to the memory card slot. This will release the memory card from the slot. Push down on the black square button next to the memory card slot. This will release the memory card from the slot. Push down on the black square button next to the memory card slot. This will release the memory card from the slot.
    • Push down on the black square button next to the memory card slot. This will release the memory card from the slot.

  7. Pull the memory card out of the memory card slot. Pull the memory card out of the memory card slot.
    • Pull the memory card out of the memory card slot.

  8. Remove two 2.4mm Phillips screws from the right side of the camera.
    • Remove two 2.4mm Phillips screws from the right side of the camera.

  9. Remove two 2.4mm Phillips screws above the label on the bottom of the camera.
    • Remove two 2.4mm Phillips screws above the label on the bottom of the camera.

    • Remove two 2.8mm Phillips screws next to the tripod hole.

  10. Remove the two 3.2mm Phillips screws that are closer to the top and bottom edges of the camera.
    • Remove the two 3.2mm Phillips screws that are closer to the top and bottom edges of the camera.

    • Remove the two 3.8mm Phillips screws on either side of the strap base.

  11. Remove one 1.6mm Phillips screw from the above the CF open button on back of the camera.
    • Remove one 1.6mm Phillips screw from the above the CF open button on back of the camera.

  12. Gently pull the front casing from the camera. The following items will either fall off or will be loose: the strap base, the gray rubber cover labeled "Digital A/V Out", and the black rubber piece over the view finder. Remove the memory card cover by sliding down the CF open button and moving the pin.
    • Gently pull the front casing from the camera.

    • The following items will either fall off or will be loose: the strap base, the gray rubber cover labeled "Digital A/V Out", and the black rubber piece over the view finder.

    • Remove the memory card cover by sliding down the CF open button and moving the pin.

  13. Gently pull the back casing from the camera. Gently pull the back casing from the camera.
    • Gently pull the back casing from the camera.

结论

To reassemble your device, follow these instructions in reverse order.

Tanya Malalang

于2011年01月12日注册

325 信誉积分

创作了3篇指南

团队

Cal Poly, Team 13-1, Forte Winter 2011 Cal Poly, Team 13-1, Forte Winter 2011 的会员

CPSU-FORTE-W11S13G1

4 名成员

创作了5篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 1

总计 1,593