简介

In this guide we will be replacing the screen of a Canon PowerShot G3.

  1. On the bottom of the camera, push and slide open the battery compartment.
    • On the bottom of the camera, push and slide open the battery compartment.

    • Remove the battery.

    添加评论

  2. Open the screen as shown.
    • Open the screen as shown.

    • Remove the screws on the end of the screen.

    添加评论

    • Remove both screws on the opposite side of the screen, located near the hinge.

    添加评论

    • Remove the back panel of the screen, using a spudger or opening tool if necessary.

    添加评论

    • Remove both screws at the top of the screen.

    • The silver bracket in between the screws will come out after removing these screws!

    添加评论

    • Turn the screen perpendicular to body of the camera.

    • Remove the screw at the base of the hinge.

    添加评论

  3. 传播 Fixmas 欢乐
    Get $12 off your purchase of $50 or more with code FIXMAS12
    传播 Fixmas 欢乐
    Get $12 off your purchase of $50 or more with code FIXMAS12
    • The screen is fragile, handle with care.

    • Push the screen down and away from the camera.

    • Remove the single screw at the base of the rotating arm. This will allow you to remove the screen cover.

    添加评论

    • Remove the black bar attached to the data ribbon cable. You will use this with the replacement.

    • The screen will be loose in the front.

    • Slide the black bar from underneath the white socket.

    • The data ribbon will remain attached to the defective screen. Both of these can be discarded.

    添加评论

    • Insert the new screen.

    • The ribbon will already be attached.

    添加评论

    • Warning: The ribbon and black bar are fragile. You will want to be very delicate with it. It will be difficult to insert.

    • Insert the ribbon into the white socket. You will have to hold this ribbon in place while placing the black bar back into the socket. You may need assistance with this part of the step.

    添加评论

    • Place the screen with monitor side out.

    • You may have to hold this in place until covers are back on properly.

    添加评论

    • Put screen cover back on and replace screw from step 7.

    添加评论

    • Turn screen up, and toward the camera. Remain perpendicular to camera.

    • Replace monitor cover using single screw, making sure cover is on the outside. (Screw from step 6)

    添加评论

    • Turn screen parallel to the camera. Refasten metal bracket with the screws from step 5.

    • These screws are small, and you may need assistance in screwing them back in.

    添加评论

    • Replace back panel. Make sure the metal part of the panel goes under the metal part of the rotating arm or the screw won't go in.

    • Put the four screws back in from step 2 and 3 respectively.

    • Step 2 screws go in the outside of the panel. Step 3 screws go in on the underside of the panel.

    添加评论

    • Replace battery into battery compartment.

    添加评论

终点

2等其他人完成本指南。

Ordonez5

于2012年09月27日注册

7 信誉积分

撰写一个指南

团队

Ohio State, Team 1-4, Buehl Fall 2012 Ohio State, Team 1-4, Buehl Fall 2012 的会员

OSU-BUEHL-F12S1G4

3 名成员

创作了1篇指南

Great instructions but where can I find a new screen? Canon doesn't carry them any more.

Hank - 回复

I'm guessing that the screen is OK and the wiring/connections is the problem.

Jon Jensen - 回复

添加评论

浏览统计数据:

过去的24小时: 1

过去的7天: 1

过去的30天: 9

总计 2,179