跳转到主内容

修复你的物品

维修的权力

商店

简介

This guide involves taking off the entire casing of the camera. It will prepare the user to perform more complicated and problem-specific repairs.

配件

没有特定配件。

  1. Slide the switch on the battery cover labeled "CARD/BATT. OPEN." to the right.
    • Slide the switch on the battery cover labeled "CARD/BATT. OPEN." to the right.

    • While still holding the switch, pull the cover down, allowing it to release and open.

  2. Tilt the camera slightly to allow the batteries to fall out.
    • Tilt the camera slightly to allow the batteries to fall out.

  3. Press on and release the memory card to eject it.
    • Press on and release the memory card to eject it.

  4. Unscrew the 5mm Phillips #00 screw from the bottom of the camera.
    • Unscrew the 5mm Phillips #00 screw from the bottom of the camera.

    • Make sure to keep the different size screws organized to make reassembling the camera simpler.

  5. 打开所有标签

    Mac的RAM升级套装

    购买套装

    所有选项卡都有足够的 RAM

    购买套装
  6. Unscrew the three 2mm Phillips #00 screws that are located on the bottom of the camera.
    • Unscrew the three 2mm Phillips #00 screws that are located on the bottom of the camera.

  7. Remove the 4mm Phillips #00 screw that is located on the left side of the camera, if the display screen is facing you.
    • Remove the 4mm Phillips #00 screw that is located on the left side of the camera, if the display screen is facing you.

  8. Take out the 4mm Phillips #00 screw under the rubber flap on the right end of the camera.
    • Take out the 4mm Phillips #00 screw under the rubber flap on the right end of the camera.

  9. Remove the second battery cover on the bottom of camera. Take the silver battery out of the camera.
    • Remove the second battery cover on the bottom of camera.

    • Take the silver battery out of the camera.

  10. Remove the 4mm Phillips #00 screw on the inside of the flap that hides the battery and memory card slots. Remove the light grey, plastic piece. Remove the plastic portion of the battery flap cover. The metal piece will remain attached.
    • Remove the 4mm Phillips #00 screw on the inside of the flap that hides the battery and memory card slots.

    • Remove the light grey, plastic piece.

    • Remove the plastic portion of the battery flap cover. The metal piece will remain attached.

  11. Slightly pull on each side of the camera. It should loosen up and come apart. If it does not pull apart right away, use a little more force. Do not give up!
    • Slightly pull on each side of the camera. It should loosen up and come apart.

    • If it does not pull apart right away, use a little more force.

    • Do not give up!

  12. Remove the back case of the camera by pulling from the top.
    • Remove the back case of the camera by pulling from the top.

    • Be careful when pulling off the case. There is a delicate gold ribbon connecting the bottom of the camera to the back case.

结论

To reassemble your device, follow these instructions in reverse order.

Stephanie Friend

于2013年01月18日注册

90 信誉积分

创作了2篇指南

团队

Cal Poly, Team 19-42, Regan Winter 2013 Cal Poly, Team 19-42, Regan Winter 2013 的会员

CPSU-REGAN-W13S19G42

4 名成员

创作了12篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 1

过去的30天: 14

总计 1,643