Skip to main content

配件

没有特定配件。

  1. Remove the eyecup by gently pushing it upwards, so it doesn't block us in the final step of pulling the back casing from the camera's body.
    • Remove the eyecup by gently pushing it upwards, so it doesn't block us in the final step of pulling the back casing from the camera's body.

  2. Remove the three 1/8" philips screws from the bottom of the back casing
    • Remove the three 1/8" philips screws from the bottom of the back casing

  3. Open the CF card compartment by moving it upwards and tilting it away from the camera body.
    • Open the CF card compartment by moving it upwards and tilting it away from the camera body.

    • Remove the two 3/16" philips screws besides the CF card slot opening.

  4. Remove the black screws from the camera's left rubber covering - note it is a 5/16" screw at the top and a 3/16" screw at the bottom.
    • Remove the black screws from the camera's left rubber covering - note it is a 5/16" screw at the top and a 3/16" screw at the bottom.

  5. Android 维修工具包

    一个新的屏幕或电池就在一个套件之内。

    现在开始购物

    Android 维修工具包

    一个新的屏幕或电池就在一个套件之内。

    现在开始购物
  6. Aided by a screwdriver or plastic opening tool, remove the rubber coating from the left side of the camera.
    • Aided by a screwdriver or plastic opening tool, remove the rubber coating from the left side of the camera.

  7. With a pointy tool, remove the soft cap covering the screw.
    • With a pointy tool, remove the soft cap covering the screw.

    • Remove the 3/16" philips screw.

  8. Use a plastic opening tool to help detaching the back casing from the camera's body.
    • Use a plastic opening tool to help detaching the back casing from the camera's body.

  9. Carefully lift the back casing from the camera's body from left to right.
    • Carefully lift the back casing from the camera's body from left to right.

  10. Locate the connector which holds the flat cable to the main circuit board. Unlock the connector by gently pulling  up its black piece from the side the flat cable comes into it. Pull the flat cable from the connector and you'll have completely removed the back casing from the camera. Note I taped each of the screws to their original places on the removed back casing, so I don't loose or mix any of them.
    • Locate the connector which holds the flat cable to the main circuit board. Unlock the connector by gently pulling up its black piece from the side the flat cable comes into it.

    • Pull the flat cable from the connector and you'll have completely removed the back casing from the camera.

    • Note I taped each of the screws to their original places on the removed back casing, so I don't loose or mix any of them.

  11. Remove the 1/4" philips screw near the carrying strap mount. Remove the 1/8" philips screw from the right side of the top casing. Remove the two 3/16" philips screws from the back of the top casing.
    • Remove the 1/4" philips screw near the carrying strap mount.

    • Remove the 1/8" philips screw from the right side of the top casing.

    • Remove the two 3/16" philips screws from the back of the top casing.

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

Claudio Felix

于2016年01月01日注册

692 Reputation

创作了7篇指南

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 1

Past 30 Days: 5

All Time: 623