简介

If the LCD swivel stops turning, or is broken by the user, this guide will help you replace it. Special care should be taken when disconnecting the LCD connector from the motherboard.

  1. Take the LCD out of its place to expose the  Phillips  #PH00 screws.
    • Take the LCD out of its place to expose the Phillips #PH00 screws.

    • Remove the two 2.5 mm Phillips #PH00 black screws on both sides of the LCD screen.

    • Next remove the two 3 mm Phillips #PH00 black screws near both sides of the base where the screen swivels.

  2. Using a plastic opening tool, carefully pry off the back cover of the LCD.
    • Using a plastic opening tool, carefully pry off the back cover of the LCD.

  3. Remove the 3 mm Phillips #PH00 silver screw on the side of the screen. Turn the screen to remove the second 3 mm Phillips #PH00 silver screw.
    • Remove the 3 mm Phillips #PH00 silver screw on the side of the screen.

    • Turn the screen to remove the second 3 mm Phillips #PH00 silver screw.

  4. Using the tweezers, carefully disconnect the rear connector by pulling it away from the screen.
    • Using the tweezers, carefully disconnect the rear connector by pulling it away from the screen.

  5. Now, four 2.2 mm Phillips  #PH00 screws holding a cover around the hinge should be visible. Turn the swivel around to expose the remaining of the aforementioned screws.
    • Now, four 2.2 mm Phillips #PH00 screws holding a cover around the hinge should be visible.

    • Turn the swivel around to expose the remaining of the aforementioned screws.

    • Then use the PH00 screw driver to remove them.

  6. 所有超过US$100或包含 Pro Tech工具包的订单免费送货!

    浏览我们的商店
  7. The eye piece will slide right off with a firm push upwards. Remove the 3.4 mm Phillips #PH00 screw using a PH00 screw driver.
    • The eye piece will slide right off with a firm push upwards.

    • Remove the 3.4 mm Phillips #PH00 screw using a PH00 screw driver.

    • Remove the two 9.9 mm Phillips #PH00 screws using the PH00 screwdriver.

  8. Using the PH00 screwdriver, remove the 3.8 mm Phillips #PH00 screw located on the back of the camera.
    • Using the PH00 screwdriver, remove the 3.8 mm Phillips #PH00 screw located on the back of the camera.

  9. Using the plastic opening tool, carefully pull up the rubber grip around the port side of the camera. Remove the  four different sized screws located beneath the rubber grip.
    • Using the plastic opening tool, carefully pull up the rubber grip around the port side of the camera.

    • Remove the four different sized screws located beneath the rubber grip.

    • 6 mm Phillips #PH00 screw.

    • 3.4 mm Phillips #PH00 screw.

    • 3.9 mm Phillips #PH00 screw.

    • 2.2 mm Phillips #PH00 screw.

  10. Using the plastic opening tool, carefully pry off the the side cover. Using the plastic opening tool, carefully pry off the the side cover.
    • Using the plastic opening tool, carefully pry off the the side cover.

  11. Remove two 4.8 mm Phillips #PH00 screws from the memory card side of camera using the PH00 screwdriver.
    • Remove two 4.8 mm Phillips #PH00 screws from the memory card side of camera using the PH00 screwdriver.

  12. Look at the bottom of the camera so the serial number tag reads up right.
    • Look at the bottom of the camera so the serial number tag reads up right.

    • Using the PH00 screw driver, remove the top three 3.5 mm Phillips #PH00 screws.

  13. Now gently pull the back cover off the camera.
    • Now gently pull the back cover off the camera.

    • Gently pull the orange wire connected to the motherboard of the camera up and off of the motherboard.

  14. Carefully pry off the LCD screen connector up from the motherboard to disconnect it, using the plastic opening tool.
    • Carefully pry off the LCD screen connector up from the motherboard to disconnect it, using the plastic opening tool.

  15. Remove one 2.8 mm Phillips #PH00 black screw on the side of the swivel assembly by using the PH00 screwdriver.
    • Remove one 2.8 mm Phillips #PH00 black screw on the side of the swivel assembly by using the PH00 screwdriver.

  16. Remove the two 2.8 mm Phillips #PH00 black screws on the back of the swivel assembly using the PH00 screwdriver.
    • Remove the two 2.8 mm Phillips #PH00 black screws on the back of the swivel assembly using the PH00 screwdriver.

结论

To reassemble your device, follow these instructions in reverse order.

3等其他人完成本指南。

Alejandro Cabrera

于2015年08月25日注册

374 信誉积分

创作了2篇指南

团队

USF Tampa, Team 16-6, Wollert Fall 2015 USF Tampa, Team 16-6, Wollert Fall 2015 的会员

USFT-WOLLERT-F15S16G6

3 名成员

创作了7篇指南

anybody know how to fix the conection that make the screen turn upside down?

yoeldiamante - 回复

thank you for the tutorial. but it is so wrong, there is no way to reasambly following the steps backward. do it for your self and you will see. there are skipping steps in the disassembly. carefoul anybody who follow this tutorial. i got lost in the reasambly. hope to can figure it out.

yoeldiamante - 回复

添加评论

浏览统计数据:

过去的24小时: 7

过去的7天: 32

过去的30天: 119

总计 6,688