菜单

你的设置

我的工作台

快速访问设备的指南，配件和论坛
我的购物车

购物车是空的

浏览我们的商店

Canon EOS 300 Side Panel with Grip Replacement

撰写者： Jordan Tang (和另外3个贡献者)
  • 评论： 0
  • 收藏 0

难度

中等

步骤

14

所需时间

10分钟

节

5

标志

0

简介

Removing the side with the grip allows for replacements on the battery door, as well as access to the top panel.

工具

购买这些工具

配件

无需配件。

  1. Open up the battery door. Open up the battery door. Open up the battery door.

    • Open up the battery door.

    翻译

  2. Remove the batteries from the camera by sliding them out into your palm. Remove the batteries from the camera by sliding them out into your palm.

    • Remove the batteries from the camera by sliding them out into your palm.

    翻译

  3. Release the side latch to open the back panel. Release the side latch to open the back panel.

    • Release the side latch to open the back panel.

    翻译

  4. Remove the two black 4.5mm screws above and below the latch. Remove the two black 4.5mm screws above and below the latch.

    • Remove the two black 4.5mm screws above and below the latch.

    翻译

  5. Using your finger, carefully pry open the side panel from the top of camera. Pull panel downwards to remove.

    • Using your finger, carefully pry open the side panel from the top of camera.

    • Pull panel downwards to remove.

    • Make sure to keep track of the small black piece of rubber under the latch.

    翻译

  6. 所有超过US$100或包含 Pro Tech工具包的订单免费送货!

    浏览我们的商店

  7. Remove the two silver 6mm Phillips #1 screws. Remove the two silver 6mm Phillips #1 screws.

    • Remove the two silver 6mm Phillips #1 screws.

    翻译

  8. Flip camera over to the bottom. Remove the one 5mm Phillips #1 silver screw.

    • Flip camera over to the bottom.

    • Remove the one 5mm Phillips #1 silver screw.

    翻译

  9. Remove the front panel by pulling away from the side with the lever. Remove the front panel by pulling away from the side with the lever.

    • Remove the front panel by pulling away from the side with the lever.

    翻译

  10. Remove three black 7.3mm Phillips #1 screws located on the corners of the camera. Remove five black 4.8mm Phillips #1 screws.

    • Remove three black 7.3mm Phillips #1 screws located on the corners of the camera.

    • Remove five black 4.8mm Phillips #1 screws.

    翻译

  11. Simply remove the bottom panel by prying it off with your finger. When removing the panel, be sure the bottom of the camera is facing upright. There are loose gears that may fall out. Be wary of a loose piece of foam attached to the bottom panel.

    • Simply remove the bottom panel by prying it off with your finger.

    • When removing the panel, be sure the bottom of the camera is facing upright. There are loose gears that may fall out.

    • Be wary of a loose piece of foam attached to the bottom panel.

    翻译

  12. Remove the remote control socket cover. Remove the remote control socket cover. Remove the remote control socket cover.

    • Remove the remote control socket cover.

    翻译

  13. Remove two black 4.5mm Phillips #1 screws. Remove two black 4.5mm Phillips #1 screws.

    • Remove two black 4.5mm Phillips #1 screws.

    翻译

  14. Remove two black 4.8mm Phillips #1 screws on the front of the camera. Remove two black 4.8mm Phillips #1 screws on the front of the camera.

    • Remove two black 4.8mm Phillips #1 screws on the front of the camera.

    翻译

  15. Pry open the side grip using a spudger. Pry open the side grip using a spudger.

    • Pry open the side grip using a spudger.

    翻译
结论

To reassemble your device, follow these instructions in reverse order.

作者

与3其他贡献者

Jordan Tang

于2014年01月24日注册

531 信誉积分

创作了5篇指南

徽章: 11

+ 8更多徽章

团队

Cal Poly, Team 6-20, Maness Winter 2014 Cal Poly, Team 6-20, Maness Winter 2014 的会员

CPSU-MANESS-W14S6G20

4 名成员

创作了11篇指南

0条评论

添加一条评论

添加评论

浏览统计数据:

过去的24小时： 0

过去的7天： 0

过去的30天： 2

总计 456