修复你的物品 社区 商店

Boosted Board 1st Generation Pulley Bearings Replacement

简介

Good bearings are essential for smooth ride. This guide will help you take out and replace the pulley bearings on the rear wheels of your Boosted Board. You can choose to replace the bearings with new ones, or just clean the existing bearings.

你所需要的

  1. Boosted Board 1st Generation Pulley Bearings Replacement, Rear Wheels: 步骤 1 中的图像 1，2 Boosted Board 1st Generation Pulley Bearings Replacement, Rear Wheels: 步骤 1 中的图像 2，2

    • Loosen the two 16.74 mm motor mount hex nut screws with a 9/64" Allen wrench.

    • Do Not Remove the Screws.

    翻译

  2. Boosted Board 1st Generation Pulley Bearings Replacement: 步骤 2 中的图像 1，1

    • Compress the motor mount back towards the wheel.

    • While keeping the motor mount compressed, tighten one of the hex nuts that you loosened in the previous step.

    • The motor mounts are spring tensioned so it is necessary compress them to loosen the belts.

    翻译

  4. Boosted Board 1st Generation Pulley Bearings Replacement: 步骤 3 中的图像 1，2 Boosted Board 1st Generation Pulley Bearings Replacement: 步骤 3 中的图像 2，2

    • Remove the axel nut with a 1/2" socket wrench

    翻译

  5. Boosted Board 1st Generation Pulley Bearings Replacement: 步骤 4 中的图像 1，3 Boosted Board 1st Generation Pulley Bearings Replacement: 步骤 4 中的图像 2，3 Boosted Board 1st Generation Pulley Bearings Replacement: 步骤 4 中的图像 3，3

    • Rotate and pull counterclockwise until the wheel comes off the axle completely.

    • The front washer will come off with the wheel.

    • Remove the back washer from the axle.

    • Replacing the wheel requires the bearings to be switched into the new wheel.

    翻译

  6. Boosted Board 1st Generation Pulley Bearings Replacement, Pulley Bearings: 步骤 5 中的图像 1，2 Boosted Board 1st Generation Pulley Bearings Replacement, Pulley Bearings: 步骤 5 中的图像 2，2

    • Use one finger to pull out the pulley bearing.

    • A good technique is to go around in a circle and lift from underneath the bearing in a carving motion.

    翻译

  7. Boosted Board 1st Generation Pulley Bearings Replacement: 步骤 6 中的图像 1，3 Boosted Board 1st Generation Pulley Bearings Replacement: 步骤 6 中的图像 2，3 Boosted Board 1st Generation Pulley Bearings Replacement: 步骤 6 中的图像 3，3

    • Place the new pulley bearing inside the gear hole and use two fingers to push down evenly until it slides into place.

    • The bearing should be flush with the gear

    翻译
结论

To reassemble your device, follow these instructions in reverse order.

作者

与4其他贡献者

Emily Imfeld

于10/06/16注册

532 声望

创作了4篇指南

徽章: 9

+ 6更多徽章

团队

Cal Poly, Team 15-7, Livingston Fall 2016 Cal Poly, Team 15-7, Livingston Fall 2016 的会员

CPSU-LIVINGSTON-F16S15G7

4 名成员

创作了6篇指南

一条评论

you mentioned cleaning bearings how do you go about that? (if rep[lacing not an option at moment) Also I noticed a single Large Bearing in my replacement kit, what is that and where do I replace it as I don’t see where it could be (I have a first Gen)

Rick Gram - 回复

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 1

过去 30 天： 2

总计 1,573